Where are you located? If in Houston TX I have a great mechanic that is cheep.
Dennis Kurk has great blue prints on where stuff is!!
Thursday, November 25, 2010
Can someone please tell me in details on how to change spark plugs on a mercedes 1998 C280?
Please be clear. I am still struggling and confused about this. Taking it to a mechanic and Benz dealer will be lots of money. Mechanic wanted $225 just for labor charge, and dealer is even more. Any help will be appreciated. Exactly where are the spark plugs located? How do i open them? Will I need some special tools? etc... Thank you!Can someone please tell me in details on how to change spark plugs on a mercedes 1998 C280?Remove spark plug suppressor, remove spark plug, reinstall suppressor. Repeat for other 11 spark plugs ( there are 2 plugs per cylinder ). The front ones are not too bad to change but the rear ones are pretty tight and you'll need a swivelling socket extension to reach them.Can someone please tell me in details on how to change spark plugs on a mercedes 1998 C280?take the spark plugs out and put the new ones in...Can someone please tell me in details on how to change spark plugs on a mercedes 1998 C280?The fact that you can't even see them tells you that it's not as easy as some people think it is,,,,,,,,,,they're located in deep holes in the cylinder head. Book time to replace the spark plugs on a 112 engine is 3.3 hours. You have to remove and replace the ignition coils (all 12 of them) and it takes a special tool to remove the wires without causing any damage (the wires are $40. each).Can someone please tell me in details on how to change spark plugs on a mercedes 1998 C280?Sorry to say. If you cant find them, have the mechanic do it. Don't go to the dealer find a smaller place that wont charge as much. You could follow the plug wires but you do need a ratchet, extender, and time. If you cross thread the plugs you will hate it and ruin the engine. Also when you change the plugs you should do the distributor and wires for plugs.
Where are you located? If in Houston TX I have a great mechanic that is cheep.
Dennis Kurk has great blue prints on where stuff is!!thin hair acne cause scarring
Where are you located? If in Houston TX I have a great mechanic that is cheep.
Dennis Kurk has great blue prints on where stuff is!!
How do i know that i would need to change my spark plugs?
what are some signs that i would need to have my spark plugs changed without actually getting under the hood and looking at them?How do i know that i would need to change my spark plugs?IF it's been awhile or if the MPG are going down and the car just doesnt seem very strong.How do i know that i would need to change my spark plugs?You should change them about every 40,000 miles... I know the dealers claim you can go 100,000 without changing them but at that point they are in real bad shape and REALLY tough to get out! If your gas mileage goes down, hard starting, or idle gets a bit shaky that is a sign as well.How do i know that i would need to change my spark plugs?I would just pull 1 out and look at it, you don't have to check everyone. If its been over 20,000 miles, they may be due anywayHow do i know that i would need to change my spark plugs?your engine seems like it running hard i had one that came out and it hit the top of the hood everytime I drove.. ,, bad gas mileage.. it could be several things.How do i know that i would need to change my spark plugs?black smoke from the pipe and the engine is running realy rough like just not normal. also just pull one out, the way it looks should tell you if you need new onesHow do i know that i would need to change my spark plugs?hard to start.....poor running....old age.....high milage.
How much to change spark plugs?
I have a 1989 toyota celica st and I am looking to put it platinum spark plugs to make it last longer. Do I have to get new wires too? How much would it be for just these two?How much to change spark plugs?platinum spark plugs can range in price anywhere from 2 dollars a piece to 8.. personally the brand u choose as your replacement would be the same as the wires.. yes the spark plugs and wires should be replaced at the same time to be able to adjust and operate the same as they wear as the years go by.. same as replacing oil filter along with new oil.. your probably looking anywhere in the range of 30 to 120 depending on how much your wanting to spendHow much to change spark plugs?plugs'll probly be $20 and wires'll probly be another $20How much to change spark plugs?go with iridium plugs, ngk makes them they are better. you do not have to replace your wires. make sure the plugs are gapped correctly.the ngk plugs are about 14-20 a plug. but worth it on the small amount of increased fuel economy. i didn't change the wires on my trans am.if you can do it yourself or ask some one to do it. you will get ripped off almost anywhere. i got quoted $285 to do the plugs in my trans am. that wasn't even counting the price of the plugs.How much to change spark plugs?If you don't have any miss firing or rough idle I wouldn't worry about the plug wires just change the plugs but use some anti seize on the threads of the plugs.This keeps them from seizing in the threads in the head of the engine.But make sure you gap the plugs before installing them.And make sure of the torque when putting them in and not to over tightening them because aluminum heads with spark plug holes will strip out them threads.Use a torque wrench if you don't have one borrow one from some body if you can't buy one from a parts store and ask what the torque should be on the plugs.How much to change spark plugs?I put Bosch twin electrode platinums in my Corolla 6 years ago and they're still good. I've ,since then , driven to Canada, Disneyland in Orange Co, Keystone Colorado and Vail Colorado, plus daily commute in the SanFrancisco Bay Area. I can talk about 60,000 miles on a set of platinum plugs and the original plug wires. Invest $10- $15 on those spark plugs and don't worry for the next 6 years at least.How much to change spark plugs?If you haven't replaced the ignition wires, cap and rotor with Denso or NGK parts within the past 50,000 miles you'd better add that to the %26quot;to do%26quot; list along with Denso or NGK platinum or longer lasting iridium spark plugs. Do not attempt to second-guess or re-gap iridium spark plugs. The center electrode is so small and hard it will spall off or break if you attempt to do so.
I need to change spark plugs in a 2000 ford ranger xlt?
I have a 2000 ford ranger xlt truck; the check engine light is on and the computer shows that #1 and #3 are misfiring; I need to change the plugs/wires, but there is not a diagram in the book, nor can i see one on the manifold/engine area.I need to change spark plugs in a 2000 ford ranger xlt?Don't change your spark plugs yet. Many other problems are much more likely unless your plugs are due to be replaced according to your Ford maintenance schedule. Many platinum tipped long life plugs are good for 80000 miles or more. You are probably in the early stages of %26quot;throwing parts at the problem%26quot;. It pays to do a little diagnosis first, especially with an engine misfire error code. However, I agree that the first order of business is to make sure your basic %26quot;tune up%26quot; and maintenance items on the truck have been maintained according to Ford's maintenance schedule. Note that you can easily damage the spark plug wires when trying to remove them from the spark plugs if your not careful, which can actually create an ignition spark problem rather than solve one.I need to change spark plugs in a 2000 ford ranger xlt?Just replace one at a time.
No diagram needed.I need to change spark plugs in a 2000 ford ranger xlt?like the guy above me, one @ a time, gap them correctly.... then reset the pcm to clear the codesI need to change spark plugs in a 2000 ford ranger xlt?What do you mean by the book. If you are talking about your owners manual. It will not be in there.
A repair manual for your ranger will show you how to do it. But i may or may not show a diagram.I need to change spark plugs in a 2000 ford ranger xlt?....have fun, the engine is quite cramed into the space...plug wires CAN be changed one by one(without mixing them up.) the wires are identified on the BOTTOM of the coil pack...the numbers shown MAY be ON THE SAME COIL which could indicate a defective coil pack. this should be checked while the coil is removed from the mounting. the wires MUST be run thru the loom to prevent damage to the new wires.I need to change spark plugs in a 2000 ford ranger xlt?look at timing also in the book and engine electrical
http://www.autozone.com/az/cds/en_us/090
go thru the fenders wells to get to the plugs
No diagram needed.I need to change spark plugs in a 2000 ford ranger xlt?like the guy above me, one @ a time, gap them correctly.... then reset the pcm to clear the codesI need to change spark plugs in a 2000 ford ranger xlt?What do you mean by the book. If you are talking about your owners manual. It will not be in there.
A repair manual for your ranger will show you how to do it. But i may or may not show a diagram.I need to change spark plugs in a 2000 ford ranger xlt?....have fun, the engine is quite cramed into the space...plug wires CAN be changed one by one(without mixing them up.) the wires are identified on the BOTTOM of the coil pack...the numbers shown MAY be ON THE SAME COIL which could indicate a defective coil pack. this should be checked while the coil is removed from the mounting. the wires MUST be run thru the loom to prevent damage to the new wires.I need to change spark plugs in a 2000 ford ranger xlt?look at timing also in the book and engine electrical
http://www.autozone.com/az/cds/en_us/090
go thru the fenders wells to get to the plugs
How do you change spark plugs and spark plug wires?
Is there a website that can show you step by step?
and what kind of spark plugs are best yet affordable?
Thank YouHow do you change spark plugs and spark plug wires?autolite is a good/cheap SP. step by step http://www.ehow.com/video_110_replace-spHow do you change spark plugs and spark plug wires?one by one with a spark plug socket. good plugs are bosch. Make sure you test the gap on your plugs though.How do you change spark plugs and spark plug wires?I don't know of any website, but you can try autozone.com. They have some how-to stuff on there so that may help. I have always had good results with champion plugs. Everyone has their own preference. You will need to know the year, make and model of your vehicle (ex. 2003 Ford Escape) and the engine size (ex. 6 cylinder, 2.4 liter). You will need a %26quot;gap guage%26quot;. The clerk at the parts store can tel you what the gap should be and show you how to use it. Start of gapping all the plugs, then remove one plug wire and only one. After remove the old plug and install the new one then put the new wire on. Repeat this process for each of the cylinders making sure to remove only one wire at a time so that you don't take a chance of mixing up 2 wires and hooking the up wrong. This would cause the cylinders to fire improperly because they are timed to fire in a certain order and mixing up the wires will mess up that order and your car won't run correctly. There may be little plastic %26quot;holders%26quot; along the wires in places. If there are, make sure the new wires go into those to keep them off the hot parts of the engine. Good luckHow do you change spark plugs and spark plug wires?take one out at a time and then just replace them...make sure you gap them
and what kind of spark plugs are best yet affordable?
Thank YouHow do you change spark plugs and spark plug wires?autolite is a good/cheap SP. step by step http://www.ehow.com/video_110_replace-spHow do you change spark plugs and spark plug wires?one by one with a spark plug socket. good plugs are bosch. Make sure you test the gap on your plugs though.How do you change spark plugs and spark plug wires?I don't know of any website, but you can try autozone.com. They have some how-to stuff on there so that may help. I have always had good results with champion plugs. Everyone has their own preference. You will need to know the year, make and model of your vehicle (ex. 2003 Ford Escape) and the engine size (ex. 6 cylinder, 2.4 liter). You will need a %26quot;gap guage%26quot;. The clerk at the parts store can tel you what the gap should be and show you how to use it. Start of gapping all the plugs, then remove one plug wire and only one. After remove the old plug and install the new one then put the new wire on. Repeat this process for each of the cylinders making sure to remove only one wire at a time so that you don't take a chance of mixing up 2 wires and hooking the up wrong. This would cause the cylinders to fire improperly because they are timed to fire in a certain order and mixing up the wires will mess up that order and your car won't run correctly. There may be little plastic %26quot;holders%26quot; along the wires in places. If there are, make sure the new wires go into those to keep them off the hot parts of the engine. Good luckHow do you change spark plugs and spark plug wires?take one out at a time and then just replace them...make sure you gap them
How hard is it to change spark plugs on a 2001 ford lightning?
I'm doing it for the first time but I want to see if I can do it by myself, and what kind of spark plugs I should use?How hard is it to change spark plugs on a 2001 ford lightning?i don't know may a branded one should dohair stylist cut 2 luxury home realtors
How do you change spark plugs on a Yamaha VStar 1100 Silverado 2005?
I need to know if I have to really pull off the gas tank in order to change the plugs on my Yamaha VStar 1100 Silverado 2005. Thanks for any help!How do you change spark plugs on a Yamaha VStar 1100 Silverado 2005?I ride a Roadstar, and yes I have to at least raise my tank up to get to all 4 plugs. I can get to2 plugs with ease.How do you change spark plugs on a Yamaha VStar 1100 Silverado 2005?with a sparkplug wrench silly.How do you change spark plugs on a Yamaha VStar 1100 Silverado 2005?there shold be two chrome covers that clip off on the tops of the engine than use the spark plug wrechHow do you change spark plugs on a Yamaha VStar 1100 Silverado 2005?try a plug wrench good luckHow do you change spark plugs on a Yamaha VStar 1100 Silverado 2005?USE YOUR TOOL KIT U GOT WITH YOUR CRUISER, ONE OF MY BIKES IS A 2003 VSTAR....VERY EASY TO GET TO AND CHANGE..BUT I HAVE TO USE FACTORY TOOLS....How do you change spark plugs on a Yamaha VStar 1100 Silverado 2005?They should be under the covers on the engine. Get yourself a manual, you're going to need it sooner or later.How do you change spark plugs on a Yamaha VStar 1100 Silverado 2005?No, but you need a socket, a short wobbly extention and a magnet.
How to Change a Pontiac Grand Prix Spark Plugs?
I have a 2000 Pontiac Grand Prix V6 that I am trying to change the Spark Plugs out off. Could someone tell me what are right tools for the Job? And what the best way to change the plugs and the cables are? Also, I no nothing about cars, but I can follow directions to a %26quot;T%26quot;.How to Change a Pontiac Grand Prix Spark Plugs?For a V-6 Grand Prix you are going to have to have some tools and a little patience and time. The Grand Prix has a transverse engine, meaning it's oriented left to right (like lots of front wheel drive cars). The spark plugs in the front are fairly easy to get at - if you have a socket wrench with a universal joint, you will get those out easily.
The back ones, by the firewall, are going to be obstructed. You didn't say if you had the 3.1 or the 3.4, but they are all difficult.You may have to remove the air cleaner housing, or the wiper arm mechanism. You can do it yourself, however, unlike the earlier GM designs that required you to put the car on a lift so you could go underneath.
Hope that helps. Email with questions.How to Change a Pontiac Grand Prix Spark Plugs?Its very simple. You need a socket wrench and a spark plug socket for the wrench. Then all you do is take them out and put in the new ones.The only hard part will be finding where they are (or at least I cannot explain it to you since I am not familiar with the car). Sorry I can't be more specific, but I have never seen the engine compartment of a 2000 Pontiac Grand Prix
The back ones, by the firewall, are going to be obstructed. You didn't say if you had the 3.1 or the 3.4, but they are all difficult.You may have to remove the air cleaner housing, or the wiper arm mechanism. You can do it yourself, however, unlike the earlier GM designs that required you to put the car on a lift so you could go underneath.
Hope that helps. Email with questions.How to Change a Pontiac Grand Prix Spark Plugs?Its very simple. You need a socket wrench and a spark plug socket for the wrench. Then all you do is take them out and put in the new ones.The only hard part will be finding where they are (or at least I cannot explain it to you since I am not familiar with the car). Sorry I can't be more specific, but I have never seen the engine compartment of a 2000 Pontiac Grand Prix
What is the most easiest way to change out the back spark plugs on my 2003 impala?
change spark plugs for 2003 impala 3.4What is the most easiest way to change out the back spark plugs on my 2003 impala?It really helps if you have a 12%26quot; 3/8 ratchet with a swivel head and a magnetic 3/8 drive 5/8 deep well socket. You do not need a 3/8 universal joint, just a very short 3/8 extension from Sears.
Husky and S%26amp;K makes a swivel head ratchet. You may get by without one as I've changed the rear plugs just fine on a 99 Pontiac Grand Prix with the 3800 V-6 with a standard 3/8 drive S%26amp;K ratchet. Don't forget to twist the spark plug boots clockwise and counterclockwise before pulling the *boot straight off. It pays to wipe on some silicone ignition grease inside the spark plug boots before snapping them back on. If you have over 75,000 miles in the original AC-Delco ignition wires now is the time to replace them. *Do not buy cheap no name ignition wires. Stick to AC-Delco or MSD wires from: autopartswarehouse.com. Don't skimp on the OEM AC-Delco iridium spark plugs either. Nothing else will last as long or run any better.What is the most easiest way to change out the back spark plugs on my 2003 impala?socket, long extentions and a couple of elbow joints... may be tricky but the right tools help...good luck..
Husky and S%26amp;K makes a swivel head ratchet. You may get by without one as I've changed the rear plugs just fine on a 99 Pontiac Grand Prix with the 3800 V-6 with a standard 3/8 drive S%26amp;K ratchet. Don't forget to twist the spark plug boots clockwise and counterclockwise before pulling the *boot straight off. It pays to wipe on some silicone ignition grease inside the spark plug boots before snapping them back on. If you have over 75,000 miles in the original AC-Delco ignition wires now is the time to replace them. *Do not buy cheap no name ignition wires. Stick to AC-Delco or MSD wires from: autopartswarehouse.com. Don't skimp on the OEM AC-Delco iridium spark plugs either. Nothing else will last as long or run any better.What is the most easiest way to change out the back spark plugs on my 2003 impala?socket, long extentions and a couple of elbow joints... may be tricky but the right tools help...good luck..
I hear it is time consuming to change spark plugs in a 99 Bravada.What is the problem and how do you do it?
I hear that one or two plugs cause the time problem.They want $180 to change them.I want to do it myself so what do I have to do?I hear it is time consuming to change spark plugs in a 99 Bravada.What is the problem and how do you do it?Not too hard loosen the steering shaft to get middle drivers side plug the others are pretty easy through wheel wells or up top. Nothing to worry about.I hear it is time consuming to change spark plugs in a 99 Bravada.What is the problem and how do you do it?not any harder than chev s-10 takes me maybe an hour remove motor mount bolt and jack up drivers side a little bit to get #3 plug out rest are done throu wheel wheel
How to change spark plugs on a 51 Renault Espcae 3L V6?
Does any body know how to change the back 3 spark plugs on a V6 3L Renault Grande Espace year 51 with out dropping the engine. Any Renault Technicians out thereHow to change spark plugs on a 51 Renault Espcae 3L V6?I can't believe that a service item like a plug change would require engine removal, no car designed in the last 40 years should be this way. Belts, chains perhaps, but not filters or plugs.
I'm no mechanic, but my wifes Focus has a large plastic valance just in front of the windscreen under the bonnet. This would have to be removed to replace the battery for example. I suppose your car, with its large capacity, transverse engine, could have the rear bank hidden under some sort of removable cover?
Is it worth investing in a Haynes manual?
Addendum: I'm not really sure where you expect this question to go. If you've already asked a Renault tech guy, what are you expecting from anyone else?How to change spark plugs on a 51 Renault Espcae 3L V6?hello dennis try using a few extensions and wobbly adapters, i havent had the luxary of doing me self but i have a strong feeling if u took it to the garage they would proberbly use adapters etcHow to change spark plugs on a 51 Renault Espcae 3L V6?AH but the joy of owning a french car. I dont know what planet they originated from, but if an ex renault technician said so then probably so. Ive had some real bears though that ive been able to put on a lift and reach up from the bottom and remove them blind with an odd assortment of adapters. They werent Renaults though.How to change spark plugs on a 51 Renault Espcae 3L V6?gas axe!rodents bird
I'm no mechanic, but my wifes Focus has a large plastic valance just in front of the windscreen under the bonnet. This would have to be removed to replace the battery for example. I suppose your car, with its large capacity, transverse engine, could have the rear bank hidden under some sort of removable cover?
Is it worth investing in a Haynes manual?
Addendum: I'm not really sure where you expect this question to go. If you've already asked a Renault tech guy, what are you expecting from anyone else?How to change spark plugs on a 51 Renault Espcae 3L V6?hello dennis try using a few extensions and wobbly adapters, i havent had the luxary of doing me self but i have a strong feeling if u took it to the garage they would proberbly use adapters etcHow to change spark plugs on a 51 Renault Espcae 3L V6?AH but the joy of owning a french car. I dont know what planet they originated from, but if an ex renault technician said so then probably so. Ive had some real bears though that ive been able to put on a lift and reach up from the bottom and remove them blind with an odd assortment of adapters. They werent Renaults though.How to change spark plugs on a 51 Renault Espcae 3L V6?gas axe!
How do I change spark plugs in a 2000 Lincoln Towncar?
Do I need to remove the fuel rail to get at the spark plugs? I have the 4.6 Litre V-8. Thank you.How do I change spark plugs in a 2000 Lincoln Towncar?this isnt a job for a beginner-take this to boys at the lincon dealershipHow do I change spark plugs in a 2000 Lincoln Towncar?noHow do I change spark plugs in a 2000 Lincoln Towncar?It does make it easier to remove the fuel rail then remove the spark plugs. It is a pretty simple task. You should be able to do it on your own as long as you know how to turn a wrench and don't over tighten them.How do I change spark plugs in a 2000 Lincoln Towncar?If you aren't familiar with basic auto maintenance, I'd recommend you have an experienced buddy help with the job. A miss aligned plug(always turn'em in by hand 2 full turns) can ruin the threads. Good luck =^ )
How do you check , and change, spark plugs in a 2000 Dodge dakota?
I want to do a little maintenance on my truck, and save money in the process by not taking it to a mechanic. Can anyone give me detailed intructions to do the spark plugs? I'm new to working on engines..How do you check , and change, spark plugs in a 2000 Dodge dakota?It's very easy. Remove the spark plug wires. Then, using a special spark plug socket (you can get this very cheap from an auto parts store) remove the spark plugs and replace them with new ones. Then put the wires back in the same way you took them out. Done!
How much does it cost to change spark plugs in a 2003 Nissan Maxima?
I found out I had water in my gas tank a few weeks ago. I use the solution to get rid of it but I am still hearing the clinging noise. Now I find out I need new spark plugs to get rid of the noise. Is this expensive? Any other way to get rid of that clinging noise?How much does it cost to change spark plugs in a 2003 Nissan Maxima?Do it yourself = $12
Mechanic = $150How much does it cost to change spark plugs in a 2003 Nissan Maxima?you can do it yourself for cheap. they only cost like $10 and you just need a socket wrench that matches the size of the plugsHow much does it cost to change spark plugs in a 2003 Nissan Maxima?i own a shop,and if you have it done ,parts and labor all together will run you around 40 bucks for this,and please have then use a good spark plug back in it, go with an ngk or a Bosch plug,don't settle for anything less,good luck hope this helps.How much does it cost to change spark plugs in a 2003 Nissan Maxima?Depending on whether or not you're having a dealer doing the work, you can more than likely buy your plugs at a local autostore such as Autozone and have them check the correct gap/clearence for you.
While the installer may not be responsible for the part unless they sold it to you, they are to be responsible for the labor!
Save yourself some money and do what you can yourself..How much does it cost to change spark plugs in a 2003 Nissan Maxima?Spark plugs range from $1-$3. You will need one for each cylinder. You also need a special socket with a rubber fitting (5/8 or 13/16). This should cost you no more than $35. This job is easy to do yourself, and if you go to a shop, you will pay at least $65 just for the labor.
Mechanic = $150How much does it cost to change spark plugs in a 2003 Nissan Maxima?you can do it yourself for cheap. they only cost like $10 and you just need a socket wrench that matches the size of the plugsHow much does it cost to change spark plugs in a 2003 Nissan Maxima?i own a shop,and if you have it done ,parts and labor all together will run you around 40 bucks for this,and please have then use a good spark plug back in it, go with an ngk or a Bosch plug,don't settle for anything less,good luck hope this helps.How much does it cost to change spark plugs in a 2003 Nissan Maxima?Depending on whether or not you're having a dealer doing the work, you can more than likely buy your plugs at a local autostore such as Autozone and have them check the correct gap/clearence for you.
While the installer may not be responsible for the part unless they sold it to you, they are to be responsible for the labor!
Save yourself some money and do what you can yourself..How much does it cost to change spark plugs in a 2003 Nissan Maxima?Spark plugs range from $1-$3. You will need one for each cylinder. You also need a special socket with a rubber fitting (5/8 or 13/16). This should cost you no more than $35. This job is easy to do yourself, and if you go to a shop, you will pay at least $65 just for the labor.
How long should it take to change spark plugs and wires in a 1994 Plymouth Voyager?
I just got my car back from the shop and was charged for three and a half hours of labor to do this work. $250 seems awfully high for spark plugs. Am I crazy?How long should it take to change spark plugs and wires in a 1994 Plymouth Voyager?If it is the V-6, the back plugs are a pain. If a 4 cyl, you got ripped.How long should it take to change spark plugs and wires in a 1994 Plymouth Voyager?i say abot 1 to 2 weeks
best answerHow long should it take to change spark plugs and wires in a 1994 Plymouth Voyager?It seems extreme, but a shop goes by the labor manual not the actual time. There is one job that I can do in under an hour, but %26quot;books out%26quot; at over seven. Guess which one is charged?How long should it take to change spark plugs and wires in a 1994 Plymouth Voyager?that seems about right, everyvan in the world is a literal ****** to work onHow long should it take to change spark plugs and wires in a 1994 Plymouth Voyager?Feel good. I'd pay it and be happy. You got a good deal if the job was done right with good parts.How long should it take to change spark plugs and wires in a 1994 Plymouth Voyager?it hard to get at the plugs in most vans but i cant say its a good price i would have done it for half of that
best answerHow long should it take to change spark plugs and wires in a 1994 Plymouth Voyager?It seems extreme, but a shop goes by the labor manual not the actual time. There is one job that I can do in under an hour, but %26quot;books out%26quot; at over seven. Guess which one is charged?How long should it take to change spark plugs and wires in a 1994 Plymouth Voyager?that seems about right, everyvan in the world is a literal ****** to work onHow long should it take to change spark plugs and wires in a 1994 Plymouth Voyager?Feel good. I'd pay it and be happy. You got a good deal if the job was done right with good parts.How long should it take to change spark plugs and wires in a 1994 Plymouth Voyager?it hard to get at the plugs in most vans but i cant say its a good price i would have done it for half of that
What is the easiest way to change spark plugs in an 06 Buick Rendezvous?
3 front plugs simple and easy to change, however the rear ones are another story! Anybody have any recommendations as to how to get to the rear plugs for someone who prefers to do their own work? (nearest garage is about a 3 hour drive so no idiot suggestions to take it to one)
2006 Buick Rendezvous CX, V6 3.5L.
I've already Googled and came up with very little, looking to hear from someone who has experience with this vehicle already.What is the easiest way to change spark plugs in an 06 Buick Rendezvous?Gm actually makes it easy. Block the wheels. Put transmission in neutral. Disconnect the engine strut arm and install a tilting tool (http://www.amazon.com/Lisle-48260-Engine
Turn the crank and it literally rotates the engine so you can reach the plugs.What is the easiest way to change spark plugs in an 06 Buick Rendezvous?gotta get them from underneath/need a liftWhat is the easiest way to change spark plugs in an 06 Buick Rendezvous?get hold of a universal swivel plug spanner with rubber ring in socket, it grips the plug when you take it outWhat is the easiest way to change spark plugs in an 06 Buick Rendezvous?I hated my Buick for the exact same reasons. You can't get to anything. Stupid battery is a side mount. You just can't get to anything. Checking or changing the oil was a task. Down the road she went. Couldn't get rid of it quick enough. Now that's my newer model. Love my '64 Buick Skylark. Pop the hood and there it is. There isn't an easy answer. I've done acrobatic works with that Buick. Come up from under neath? The new Buicks just suck. I feel your pain and I sold mine. Eff the hassle.What is the easiest way to change spark plugs in an 06 Buick Rendezvous?You will have to use some extensions on your 3/8%26quot; ratchet wrench and an elbow or universal joint that allows the second extension to connect to the first extension so you can allow the plug socket and the extension connected to the plug socket to stay straight while you turn your wrench at an odd angle like maybe 45 degrees.
You may need a 3%26quot; extension on the plug socket and maybe a 4%26quot;-6%26quot; extension on the wrench to clear the clutter so you can turn the wrench and back the plug out of the head. Or you may need a 4%26quot;-6%26quot; extension on the plug socket and a 3%26quot; extension on the wrench. The elbow joint or universal joint will allow you to back it out safely without breaking the plug or stripping the head or installing the new plugs cross-threaded.
Patience is the key to doing it right without boogering up the head. As long as you have good purchase on the spark plug with the socket and your extensions and universal joint are connected properly and you can turn the wrench even partially you can get the plugs out slowly, one partial turn at a time.
When you are ready to put the new plugs in the head, recommend you do one plug at a time so you don't cross your wires, put a little anti-seize on the threads of the new plug(s) and start them by hand before you connect the wrench. This way you will not be forcing the new plugs into the hole crooked and will not cross-thread the plug into the head. Tighten them down to %26quot;snug%26quot; not superman tight. I like to use electrical grease on plug boots so they are less likely to stick to the spark plug insulators so next tune-up you don't have a hassle pulling to plug wires off the plugs.
Good Luck!remedy for acne scars anyway to look at someone
2006 Buick Rendezvous CX, V6 3.5L.
I've already Googled and came up with very little, looking to hear from someone who has experience with this vehicle already.What is the easiest way to change spark plugs in an 06 Buick Rendezvous?Gm actually makes it easy. Block the wheels. Put transmission in neutral. Disconnect the engine strut arm and install a tilting tool (http://www.amazon.com/Lisle-48260-Engine
Turn the crank and it literally rotates the engine so you can reach the plugs.What is the easiest way to change spark plugs in an 06 Buick Rendezvous?gotta get them from underneath/need a liftWhat is the easiest way to change spark plugs in an 06 Buick Rendezvous?get hold of a universal swivel plug spanner with rubber ring in socket, it grips the plug when you take it outWhat is the easiest way to change spark plugs in an 06 Buick Rendezvous?I hated my Buick for the exact same reasons. You can't get to anything. Stupid battery is a side mount. You just can't get to anything. Checking or changing the oil was a task. Down the road she went. Couldn't get rid of it quick enough. Now that's my newer model. Love my '64 Buick Skylark. Pop the hood and there it is. There isn't an easy answer. I've done acrobatic works with that Buick. Come up from under neath? The new Buicks just suck. I feel your pain and I sold mine. Eff the hassle.What is the easiest way to change spark plugs in an 06 Buick Rendezvous?You will have to use some extensions on your 3/8%26quot; ratchet wrench and an elbow or universal joint that allows the second extension to connect to the first extension so you can allow the plug socket and the extension connected to the plug socket to stay straight while you turn your wrench at an odd angle like maybe 45 degrees.
You may need a 3%26quot; extension on the plug socket and maybe a 4%26quot;-6%26quot; extension on the wrench to clear the clutter so you can turn the wrench and back the plug out of the head. Or you may need a 4%26quot;-6%26quot; extension on the plug socket and a 3%26quot; extension on the wrench. The elbow joint or universal joint will allow you to back it out safely without breaking the plug or stripping the head or installing the new plugs cross-threaded.
Patience is the key to doing it right without boogering up the head. As long as you have good purchase on the spark plug with the socket and your extensions and universal joint are connected properly and you can turn the wrench even partially you can get the plugs out slowly, one partial turn at a time.
When you are ready to put the new plugs in the head, recommend you do one plug at a time so you don't cross your wires, put a little anti-seize on the threads of the new plug(s) and start them by hand before you connect the wrench. This way you will not be forcing the new plugs into the hole crooked and will not cross-thread the plug into the head. Tighten them down to %26quot;snug%26quot; not superman tight. I like to use electrical grease on plug boots so they are less likely to stick to the spark plug insulators so next tune-up you don't have a hassle pulling to plug wires off the plugs.
Good Luck!
How hard is it to change spark plugs on a 2000 Pontiac Montana?
its a 6 cylinder. what all needs to be done to access the spark plugs on the firewall side?How hard is it to change spark plugs on a 2000 Pontiac Montana?Ugh! Don't you know they make it so you can't change the spark plugs on anything anymore? I think you will have to disassemble the entire car to access them. Good luck.How hard is it to change spark plugs on a 2000 Pontiac Montana?Pull your plug wires out one at a time. and by one at a time, I mean pull one wire, replace the plug and then replace the wire. If you pull them all off and then forget where each one goes, well, you can figure it out.
How do I change my spark plugs on my 1993 buick park avenue?
How do I get to my spark plugs to change them plugs??
Also how do I get to my starter to check it/ where is the starter located??
ANYONE WITH PRIOR EXPERIENCE WOULD REALLY HELP, THANKS IN ANDVANCE!How do I change my spark plugs on my 1993 buick park avenue?I don't understand the question about the spark plugs.
As far as the starter, it's on the side of the motor facing the radiator, just in front of the transmission.
http://econtent.autozone.com:24991/znetr
Also how do I get to my starter to check it/ where is the starter located??
ANYONE WITH PRIOR EXPERIENCE WOULD REALLY HELP, THANKS IN ANDVANCE!How do I change my spark plugs on my 1993 buick park avenue?I don't understand the question about the spark plugs.
As far as the starter, it's on the side of the motor facing the radiator, just in front of the transmission.
http://econtent.autozone.com:24991/znetr
I need to know how to change spark plugs in a 2004 chevy aveo?
i can change spark plugs. but i was confused when i opened the hood there was a box next to it %26amp; no spark plugs how do i go by changing them.I need to know how to change spark plugs in a 2004 chevy aveo?Remove the hex head bolts (4), and pull the cover up. Remove the plug wires and plugs one at a time. Don't forget to use a small amount of anti-seize on the new plug threads.
Have you had the timing belt replaced yet? The service interval is 60k miles, and the engine can be severely damaged if it breaks.I need to know how to change spark plugs in a 2004 chevy aveo?you first need to remove the black cover that goes cover the engine, it has to be removed before you can see the spark plug wires under it, it may require allan wrenchI need to know how to change spark plugs in a 2004 chevy aveo?never worked on an aveo but i looked at a picture on the web and it looks like there is a plastic cover that has to be removed. if your looking at the engine on the drivers side you can see the ignition box with the spark plug wires coming out and going under the cover. looks like four screws hold it in place. take that off and the follow the wires. you might need a long extention to get at them as this is a dohc engine and the plugs might be deep in the engine.I need to know how to change spark plugs in a 2004 chevy aveo?take the spark plug caps off, put wrench on plugs. turn left, remove. insert new plugs, put wrench on plugs, turn right, re insert caps on plugs.
Have you had the timing belt replaced yet? The service interval is 60k miles, and the engine can be severely damaged if it breaks.I need to know how to change spark plugs in a 2004 chevy aveo?you first need to remove the black cover that goes cover the engine, it has to be removed before you can see the spark plug wires under it, it may require allan wrenchI need to know how to change spark plugs in a 2004 chevy aveo?never worked on an aveo but i looked at a picture on the web and it looks like there is a plastic cover that has to be removed. if your looking at the engine on the drivers side you can see the ignition box with the spark plug wires coming out and going under the cover. looks like four screws hold it in place. take that off and the follow the wires. you might need a long extention to get at them as this is a dohc engine and the plugs might be deep in the engine.I need to know how to change spark plugs in a 2004 chevy aveo?take the spark plug caps off, put wrench on plugs. turn left, remove. insert new plugs, put wrench on plugs, turn right, re insert caps on plugs.
How do I change SPARK PLUGS?
I have a 2004 Jeep Liberty (if that matters)
I just bought the plugs, but what tools do people usually use to change plugs out?
Thanks.How do I change SPARK PLUGS?a 5/8 or 9/16 socket an rachet extstionHow do I change SPARK PLUGS?A ranch and an 3h socket.How do I change SPARK PLUGS?Depending on the spark plug itself, you will need a screw driver, a socket wrench and some gloves (if you dont want your hands to get dirty or irritated by cold/hot metal)
1) Take the plug out of the package (Be sure it fits correctly into the required position)
2) Be sure your car is not running while you are doing the exchange/replacement
3) Remove the old plug from its socket
4) Put in the new one and screw it in tightly with your hand before using the socket wrench and/or screw driver to tighten it further.
5) Once its tight, close the spark plug box (If it has one) and make sure its secure..
ALL DONE
If you check out the site i gave you in my %26quot;Source%26quot; you can get some more light shed on the situation if your still having trouble. Good luck!How do I change SPARK PLUGS?http://wiki.answers.com/Q/How_do_you_chaHow do I change SPARK PLUGS?ratchet , extensions, spark plug gap-per , don't over torque them down 5/8 or 13/16 plug socketHow do I change SPARK PLUGS?get a ratchet, a 5/8 plug socket and maybe an extension. twist the boot on the plug and pull the plug wire off but 1 at a time. put the socket on the plug and use the extension ( if you need to ) and use the ratchet and turn to the left to take them out. before putting the new plugs in make sure you gap them. run the plug in and snug them up and put on the plug wire and go to the rest of them.How do I change SPARK PLUGS?get a 5/8 inch spark plug socket, a swivel adapter, at least a 6 inch extension for the wratchet, and a wratchet. you will need to check the gap on the plugs, I recomend getting the parts store to show you how, if you can find a short piece of 3/8 fuel hose you can slip it on the head of the plugs and use it to easilly install the new plugs till snug, then use the spark plug socket to tighten the plugs. they only need a tiny bit dont get to aggressive with it. I recomend using a dab of anti seize on the threads of the new plugs for future removal. the old plugs have to be removed to the left direction (counter clock wise) and are tightened to the clock wise directionHow do I change SPARK PLUGS?spark plug socket and rachetHow do I change SPARK PLUGS?Once somebody shows you how to change spark plugs you may wonder why you thought it was difficult. In some cars it is difficult.
You need a sparkplug socket to remove and replace the spark plug. It is tight enough to keep it from working its way loose. You have the plugs. You should put antiseize compound on the threads of the new plugs before you put them in, but I use a couple of drops of clean motor oil. You should have a gap tool to make sure the gap on the sparkplug electrode is the right size. If you're using platinum plugs they say don't try and adjust their gap. They're usually right, but I always check to make sure.
Remove the spark plugs only one at a time to make sure you don't have a chance of mixing the wires up. Do the job with the engine cold, if you can.
Take off the first wire from the first sparkplug by twisting its rubber cover to make sure it doesn't stick to the plug, then pull the connector loose from the sparkplug. Next, carefully slip the socket down onto the sparkplug and loosen it. If it seems like it doesn't want to turn freely, turn it back and forth a bit, then unscrew it all the way out, taking care to not drop it while you lift it out of its hole. Take time to look at the condition of the plug. It should be dry, not oily or wet with fuel. If there is any water on it you have a serious problem with the engine. It should be brown like light coffee, or grey, but not black and sooty. Take a new sparkplug out of its box and look at it to make sure its gasket is on it and all the way off the threads. Look at the electrode and make sure it is straight. Is some clumsy clerk dropped it in the store it could be bent. That doesn't happen often, but this is your chance to be sure. Measure the gap to make sure it's not open too much or closed too much. Standard plugs can be bent open or closed as necessary. Put a drop of antiseize compund on the threads, wipe off the excess .Here's where you need to be careful: Slowly start the new plug screwing into the hole by hand to make sure it goes in straight. Make certain this is straight. Easy is right. Hard is always if it's crooked. Never force it. Screw the sparkplug all the way down with the socket, then tighten it a half to 3/4 turn more. I use a torque wrench to get it to 14 foot pounds, but that's just being very cautious. As long as its tight enough to stay in will do. Try and remember how hard the old one was to lossen and that's how tight to put the new one in. Replace the wire to the new plug, making sure it is firmly attached and you're done. Do the next plug now, the same way. You'll be glad you don't have two loose wires and wonder which plug they came off off. There is only one right way to put them, so the one-by-one method is foolproof.
If a sparkplug won't come out with your hand tools, there is a real problem you'll need an experienced person to assay. The last thing you want to do is start out with a simple job and end up having to take off the head to have it repaired. Think of the last time you opened a real tight jar. It shouldn't be harder than that. You can learn everything you need to know about doing this basic job in a Chiltons Auto Repair manual. There is very little else you would need to do with that particular engine to keep it running well. Replace the air filter and change the oil and oil filter next chance you have time, unless that's been done in the last 6 months. A good investment, however, is to buy an OBD II code reader so you can tell what's wrong anytime the check engine light comes on. It'll cost you about $100 and it just about costs double that anytime you go to the service dept to have work done. You're saving over $100 changing your own spark plugs. Reward yourself.
I just bought the plugs, but what tools do people usually use to change plugs out?
Thanks.How do I change SPARK PLUGS?a 5/8 or 9/16 socket an rachet extstionHow do I change SPARK PLUGS?A ranch and an 3h socket.How do I change SPARK PLUGS?Depending on the spark plug itself, you will need a screw driver, a socket wrench and some gloves (if you dont want your hands to get dirty or irritated by cold/hot metal)
1) Take the plug out of the package (Be sure it fits correctly into the required position)
2) Be sure your car is not running while you are doing the exchange/replacement
3) Remove the old plug from its socket
4) Put in the new one and screw it in tightly with your hand before using the socket wrench and/or screw driver to tighten it further.
5) Once its tight, close the spark plug box (If it has one) and make sure its secure..
ALL DONE
If you check out the site i gave you in my %26quot;Source%26quot; you can get some more light shed on the situation if your still having trouble. Good luck!How do I change SPARK PLUGS?http://wiki.answers.com/Q/How_do_you_chaHow do I change SPARK PLUGS?ratchet , extensions, spark plug gap-per , don't over torque them down 5/8 or 13/16 plug socketHow do I change SPARK PLUGS?get a ratchet, a 5/8 plug socket and maybe an extension. twist the boot on the plug and pull the plug wire off but 1 at a time. put the socket on the plug and use the extension ( if you need to ) and use the ratchet and turn to the left to take them out. before putting the new plugs in make sure you gap them. run the plug in and snug them up and put on the plug wire and go to the rest of them.How do I change SPARK PLUGS?get a 5/8 inch spark plug socket, a swivel adapter, at least a 6 inch extension for the wratchet, and a wratchet. you will need to check the gap on the plugs, I recomend getting the parts store to show you how, if you can find a short piece of 3/8 fuel hose you can slip it on the head of the plugs and use it to easilly install the new plugs till snug, then use the spark plug socket to tighten the plugs. they only need a tiny bit dont get to aggressive with it. I recomend using a dab of anti seize on the threads of the new plugs for future removal. the old plugs have to be removed to the left direction (counter clock wise) and are tightened to the clock wise directionHow do I change SPARK PLUGS?spark plug socket and rachetHow do I change SPARK PLUGS?Once somebody shows you how to change spark plugs you may wonder why you thought it was difficult. In some cars it is difficult.
You need a sparkplug socket to remove and replace the spark plug. It is tight enough to keep it from working its way loose. You have the plugs. You should put antiseize compound on the threads of the new plugs before you put them in, but I use a couple of drops of clean motor oil. You should have a gap tool to make sure the gap on the sparkplug electrode is the right size. If you're using platinum plugs they say don't try and adjust their gap. They're usually right, but I always check to make sure.
Remove the spark plugs only one at a time to make sure you don't have a chance of mixing the wires up. Do the job with the engine cold, if you can.
Take off the first wire from the first sparkplug by twisting its rubber cover to make sure it doesn't stick to the plug, then pull the connector loose from the sparkplug. Next, carefully slip the socket down onto the sparkplug and loosen it. If it seems like it doesn't want to turn freely, turn it back and forth a bit, then unscrew it all the way out, taking care to not drop it while you lift it out of its hole. Take time to look at the condition of the plug. It should be dry, not oily or wet with fuel. If there is any water on it you have a serious problem with the engine. It should be brown like light coffee, or grey, but not black and sooty. Take a new sparkplug out of its box and look at it to make sure its gasket is on it and all the way off the threads. Look at the electrode and make sure it is straight. Is some clumsy clerk dropped it in the store it could be bent. That doesn't happen often, but this is your chance to be sure. Measure the gap to make sure it's not open too much or closed too much. Standard plugs can be bent open or closed as necessary. Put a drop of antiseize compund on the threads, wipe off the excess .Here's where you need to be careful: Slowly start the new plug screwing into the hole by hand to make sure it goes in straight. Make certain this is straight. Easy is right. Hard is always if it's crooked. Never force it. Screw the sparkplug all the way down with the socket, then tighten it a half to 3/4 turn more. I use a torque wrench to get it to 14 foot pounds, but that's just being very cautious. As long as its tight enough to stay in will do. Try and remember how hard the old one was to lossen and that's how tight to put the new one in. Replace the wire to the new plug, making sure it is firmly attached and you're done. Do the next plug now, the same way. You'll be glad you don't have two loose wires and wonder which plug they came off off. There is only one right way to put them, so the one-by-one method is foolproof.
If a sparkplug won't come out with your hand tools, there is a real problem you'll need an experienced person to assay. The last thing you want to do is start out with a simple job and end up having to take off the head to have it repaired. Think of the last time you opened a real tight jar. It shouldn't be harder than that. You can learn everything you need to know about doing this basic job in a Chiltons Auto Repair manual. There is very little else you would need to do with that particular engine to keep it running well. Replace the air filter and change the oil and oil filter next chance you have time, unless that's been done in the last 6 months. A good investment, however, is to buy an OBD II code reader so you can tell what's wrong anytime the check engine light comes on. It'll cost you about $100 and it just about costs double that anytime you go to the service dept to have work done. You're saving over $100 changing your own spark plugs. Reward yourself.
How Do I Change Spark Plugs On A Renault Megane?? please help?
Hi there
Hope someone can help me. I need to change the spark plugs on my Renault Megane 03 reg, as the car seems to be misfiring ive changed the coils and can see the spark plugs but how do i get to them? they seem like they are to far down to reach..Also if any one knows if there could be any other problems as to why my car is misfiring it would help. the warning engine light flashes sometimes and at low speed the car really runs bad like its going to stall but at a faster speed it seems ok. i would take it to a garage but funds are a bit low at the moment.
Thank you to anyone that could help....How Do I Change Spark Plugs On A Renault Megane?? please help?You need to use a spark plug socket with two short extensions, try to use the spark plug socket that has a rubber ring on the inside to hold the spark plug securely as its a long drop from the top of the engine cover to the bottom of the hole for the spark plug.
Importantly when you have all four spark plugs out, look at the condition of the ends of the spark plug as this will give a good indication of what problems there is within the engine.
All four spark plugs should look more or less the same with a light gray deposit coating the ends of the electrodes.
The plug gap should be more or less the same of all four.How Do I Change Spark Plugs On A Renault Megane?? please help?If you lived in portland or. I would do what I could! There are so many things that could cause this,My best answer is get a friend, neighbor, DAD! to help you. IMM TRULY SORRY!! MERRILL!How Do I Change Spark Plugs On A Renault Megane?? please help?Spark plug socket, 6 inch extention and a ratchet are all you need to reach the plugs. if you have changed out the coil pack you will most likely have solved the misfire problem. finish off the plugs and you should be set.How Do I Change Spark Plugs On A Renault Megane?? please help?buy your spark plugs, and buy a spark plug tool at the same time, this way you will be sure your tool fits the spark plug, as there can be two sizes.
or buy a socket set ,they usually have a spark plug removal tool/socket in them.
just be careful taking them out and putting them in, usually the heads are aluminum, make sure you don't cross thread them. or over tighten themHow Do I Change Spark Plugs On A Renault Megane?? please help?hi there if you are going to change the plugs you need long nose plyers to get them out just loosen them as normal them putthe plyer in the hole to pull them out ,i would get the air mass sensor and the lambda sensor checked as well or go th a garage and ask them to put the computer on them it will tell you what the problem is or just get them to reset the light
hope this helpsHow Do I Change Spark Plugs On A Renault Megane?? please help?Take em out and put the new ones in simple initHow Do I Change Spark Plugs On A Renault Megane?? please help?haynes manual?games name of song
Hope someone can help me. I need to change the spark plugs on my Renault Megane 03 reg, as the car seems to be misfiring ive changed the coils and can see the spark plugs but how do i get to them? they seem like they are to far down to reach..Also if any one knows if there could be any other problems as to why my car is misfiring it would help. the warning engine light flashes sometimes and at low speed the car really runs bad like its going to stall but at a faster speed it seems ok. i would take it to a garage but funds are a bit low at the moment.
Thank you to anyone that could help....How Do I Change Spark Plugs On A Renault Megane?? please help?You need to use a spark plug socket with two short extensions, try to use the spark plug socket that has a rubber ring on the inside to hold the spark plug securely as its a long drop from the top of the engine cover to the bottom of the hole for the spark plug.
Importantly when you have all four spark plugs out, look at the condition of the ends of the spark plug as this will give a good indication of what problems there is within the engine.
All four spark plugs should look more or less the same with a light gray deposit coating the ends of the electrodes.
The plug gap should be more or less the same of all four.How Do I Change Spark Plugs On A Renault Megane?? please help?If you lived in portland or. I would do what I could! There are so many things that could cause this,My best answer is get a friend, neighbor, DAD! to help you. IMM TRULY SORRY!! MERRILL!How Do I Change Spark Plugs On A Renault Megane?? please help?Spark plug socket, 6 inch extention and a ratchet are all you need to reach the plugs. if you have changed out the coil pack you will most likely have solved the misfire problem. finish off the plugs and you should be set.How Do I Change Spark Plugs On A Renault Megane?? please help?buy your spark plugs, and buy a spark plug tool at the same time, this way you will be sure your tool fits the spark plug, as there can be two sizes.
or buy a socket set ,they usually have a spark plug removal tool/socket in them.
just be careful taking them out and putting them in, usually the heads are aluminum, make sure you don't cross thread them. or over tighten themHow Do I Change Spark Plugs On A Renault Megane?? please help?hi there if you are going to change the plugs you need long nose plyers to get them out just loosen them as normal them putthe plyer in the hole to pull them out ,i would get the air mass sensor and the lambda sensor checked as well or go th a garage and ask them to put the computer on them it will tell you what the problem is or just get them to reset the light
hope this helpsHow Do I Change Spark Plugs On A Renault Megane?? please help?Take em out and put the new ones in simple initHow Do I Change Spark Plugs On A Renault Megane?? please help?haynes manual?
2002 KIA sedona how do i change spark plugs and wires?
its a 2002 kia sedona DOHC.v6 i cant see where the spark plugs are at how do i change them. its time. please help.2002 KIA sedona how do i change spark plugs and wires?An 02 kia sedona van with a v6 hmm the spark plugs or under the plastic shroud three on each head they may have a separate coil on each one if this is this case a ten millimeter screw holds the coil down on the plug once out is removed the plug can be taken out with a 5/8 socket and extension on your ratchet the head closer to the front will be easy the one closer to the fire wall wi be a little more difficult and dont forget to gap your spark plugs unless u purchase NGK spark plugs these or pre gapped and also recommended for the kia...2002 KIA sedona how do i change spark plugs and wires?look under the intake manifold
Why is car vibrates after spark plugs change?
Just changed spark plugs from 02 lancer. I noticed it vibrates a bit esp when im on stop. And also when you step on the gas pedal it accelerates right away like so fast. What have I might done wrong? ThanksWhy is car vibrates after spark plugs change?maan, you may have done several comon mistakes. 1st did you gap the plugs all to the required gap? sometimes plugs are pre gapped but never trust this! a plug can be accidentally dropped or wrongly set. 2nd connected fully on the plug. a spark plug boot most times is a snug fit and people often think its seated on the plug but the metal spring cap may be just touching and not fully engaging. 3rd %26quot;1,2,3,4 or was it 1324 oops%26quot; its shocking how easy we can mix 2 wires, sorry for the pun. lastly damage to the plug wire from hard removal or damage to the plug from a poor fitting spark plug socket. the insulator for a plug is ceramic, a type of glass and they arent user friendly a cracked insulator can allow arcing between the plug and the cylinder fouling the plug and as to the wire most are a carbon core. they handle heat, carry voltage,flex to the angle needed but dont like tugging. also most plug boots are sylicone rubber to resist heat ,oil, moisture etc but with use and time become weakened and can rip. again arcing can ocur.Why is car vibrates after spark plugs change?you should make sure the plugs are properly gapped to spec that could be a problem also check wires or coils and make sure none are loose or bad
How do I change spark plugs on a 02 Jetta 2.0? Is it relatively hard?
I own a 2002 jetta gls and at 40k, the spark plugs need to be changed. I would like to know what the steps are to change them and if it is a hard job to conquer.How do I change spark plugs on a 02 Jetta 2.0? Is it relatively hard?Buy the replacement plugs first.
I am guessing you know how to get to the plugs, so i advise u to make sure the engine is cold, say first thing in the morning. Never pull plugs when motor is hot or at operating temperature as this can sometimes have a negative effect on an otherwise easy job.
Ok so motor is cold u have access to spark plugs and the needed tools; Remove the spark plug lead dont just pull on the lead try to gently use the insulating boot around plug the black rubber bit closest to the spark plug, before undoing the plugs try to tighten the spark plug a very little amount as this seats the thread on the plug, once plug has been tightened fractionally undo plug and insert new plug into same location.
When inserting new plug try to get the thread to bite by screwing it in with your fingers if possible, that is until you have to use the ratchet. At this point i will advise that if the plug isn't going in as easy as it came out then STOP and make sure you are not cross threading the plug. Just undo it and start again.OK so finger tight, good; Next using the ratchet tighten the plug firmly, i cant help u here as this is usual done by feel. If u remember how hard it was to take out the plug then this is a good indication of tightness needed.
Make sense?
That's about it, continue on with process until all plugs are changed.
Change one plug at a time and take note of where it came from, then lay all plugs in sequence as per removal. Take note of any irregularities of the plugs. On removal of first plug compare electrode gap and correct new plug gap if needed, usually not as spark plugs gapping is not really an issue on modern cars (anything with a computer in it.)How do I change spark plugs on a 02 Jetta 2.0? Is it relatively hard?Wait ten thousand more miles and get a mechanic to do it. Jettas' are worse than Jaguars on repairing them and cost.How do I change spark plugs on a 02 Jetta 2.0? Is it relatively hard?You just need to pull your plug connectors and have a plug socket and rench its quick and easy. The only part to pay attention to is when you use the new ones make sure you have the tool to set the proper span between the gap. Should be found online.How do I change spark plugs on a 02 Jetta 2.0? Is it relatively hard?Fairly easy repair. Just remove the engine cover and you should be able to see the plugs on the front of the engine. It helps if you have a swivel spark plug socket, b/c you have to work around the intake manifold.
I am guessing you know how to get to the plugs, so i advise u to make sure the engine is cold, say first thing in the morning. Never pull plugs when motor is hot or at operating temperature as this can sometimes have a negative effect on an otherwise easy job.
Ok so motor is cold u have access to spark plugs and the needed tools; Remove the spark plug lead dont just pull on the lead try to gently use the insulating boot around plug the black rubber bit closest to the spark plug, before undoing the plugs try to tighten the spark plug a very little amount as this seats the thread on the plug, once plug has been tightened fractionally undo plug and insert new plug into same location.
When inserting new plug try to get the thread to bite by screwing it in with your fingers if possible, that is until you have to use the ratchet. At this point i will advise that if the plug isn't going in as easy as it came out then STOP and make sure you are not cross threading the plug. Just undo it and start again.OK so finger tight, good; Next using the ratchet tighten the plug firmly, i cant help u here as this is usual done by feel. If u remember how hard it was to take out the plug then this is a good indication of tightness needed.
Make sense?
That's about it, continue on with process until all plugs are changed.
Change one plug at a time and take note of where it came from, then lay all plugs in sequence as per removal. Take note of any irregularities of the plugs. On removal of first plug compare electrode gap and correct new plug gap if needed, usually not as spark plugs gapping is not really an issue on modern cars (anything with a computer in it.)How do I change spark plugs on a 02 Jetta 2.0? Is it relatively hard?Wait ten thousand more miles and get a mechanic to do it. Jettas' are worse than Jaguars on repairing them and cost.How do I change spark plugs on a 02 Jetta 2.0? Is it relatively hard?You just need to pull your plug connectors and have a plug socket and rench its quick and easy. The only part to pay attention to is when you use the new ones make sure you have the tool to set the proper span between the gap. Should be found online.How do I change spark plugs on a 02 Jetta 2.0? Is it relatively hard?Fairly easy repair. Just remove the engine cover and you should be able to see the plugs on the front of the engine. It helps if you have a swivel spark plug socket, b/c you have to work around the intake manifold.
How do you change spark plugs on a 98 rodeo?
I would like to tune up my car myself my step father showed me how to change spark plugs and i don't remember please explain the easiest way if you can how to do a tune up including oil change and any suggestions on what the best oil would to be use to clean out your engine I really don't know how to word it but hopefully someone understands what I'm trying to ask THX!How do you change spark plugs on a 98 rodeo?you don,t use motor oil to clean out the engine, you use motor flush. as for the plugs you will need a 3/8 ratchet and spark plug socket and maybe an extensionHow do you change spark plugs on a 98 rodeo?Change them one at a time, pull the spark plug wire off one, remove and replace the plug and put the wire back on and move to the next one, making sure you have the wire on snug and tight on the plug,(make sure the spark plugs are gapped correctly B-4 starting. If you are changing the distributor cap and rotor be sure to mark your wires so you know where they go into the cap, or your car may not start. For an oil change, crawl under the car, place a container that can hold at least 5 qts. under your oil pan drain plug and remove the plug, opening your filler cap will help it drain quicker. After it has drained all out, use a filter wrench and remove your oil filter, put a little oil on the rubber gasket on the new filter and put it back on your car by getting it hand tightened and using the wrench to tighten it another 1/4 turn. Put your drain plug back on your oil pan and tighten.
Fill your car up with required amount of oil, maybe 4 qts first if it takes 5, start your motor to circulate the oil through the motor and filter, turn it off and add the remaining quart. You might want to change your air filter also if you have a new one.
5w-30 or 10w-30 should be right for the oil.
SPARK PLUG GAP....every car has a certain amount of gap in the plug to make sure it fires at its optimum...here is a link that may explain better along with some other useful stuff. Find out what the gap is for your car from where you bought the plugs and they can tell you and even check it for you.
Here is the link: http://www.ehow.com/video_2326846_set-sp
BTW....you don't need a torgue wrench to replace the plugs, just a ratchet wrench, a spark plug socket(rubber gasket inside the socket), and an extension. tighten it , just don't over tighten it.....as shown in video.How do you change spark plugs on a 98 rodeo?To add to it:
Remove the oil filler cap first before draining the oil. I know it's very rare that one can't open it, but it'll be a big headache if you drain the oil and then can't fill it.
Know the a torque setting and use a torque wrench.
Double check on the spark plug's gap.
Consider using a little anti-seize on the spark plug. Some have a coating on it already, some people don't use it. Just consider it.
Fill your car up with required amount of oil, maybe 4 qts first if it takes 5, start your motor to circulate the oil through the motor and filter, turn it off and add the remaining quart. You might want to change your air filter also if you have a new one.
5w-30 or 10w-30 should be right for the oil.
SPARK PLUG GAP....every car has a certain amount of gap in the plug to make sure it fires at its optimum...here is a link that may explain better along with some other useful stuff. Find out what the gap is for your car from where you bought the plugs and they can tell you and even check it for you.
Here is the link: http://www.ehow.com/video_2326846_set-sp
BTW....you don't need a torgue wrench to replace the plugs, just a ratchet wrench, a spark plug socket(rubber gasket inside the socket), and an extension. tighten it , just don't over tighten it.....as shown in video.How do you change spark plugs on a 98 rodeo?To add to it:
Remove the oil filler cap first before draining the oil. I know it's very rare that one can't open it, but it'll be a big headache if you drain the oil and then can't fill it.
Know the a torque setting and use a torque wrench.
Double check on the spark plug's gap.
Consider using a little anti-seize on the spark plug. Some have a coating on it already, some people don't use it. Just consider it.
How often should i change spark plugs?
i have a '02 corolla -- should i change my spark plugs at the 60k mile checkup/maintanance? what else do i need to do at 60k miles?How often should i change spark plugs?plugs for non platinum change then around 30k for platinum plugs anywhere from 60 to 100k, at the 60k service the trans, oil change every 3000 miles unless you use synthetic then around 5000 to 6000 miles. coolant service, injector cleaning, pcv every 15 to 30k, fuel filter every 15k.How often should i change spark plugs?change spark plugs every year regardless of mileage, normal servicing annually although i would change oil %26amp; filter every six monthsHow often should i change spark plugs?check your owners manual for maintenance schedules. It will tell you there what they recommend. I usually don't go over 60K however. The manual will tell what you should do or should have done. Make not of whether you are %26quot;normal or severe%26quot; service. Most people fall into the severe category.How often should i change spark plugs?your spark plugs should be changed every 45,000 miles...every 10,000 miles you filster need to be changed(fuel filters)....How often should i change spark plugs?Depends, are they platinum or standard resister plugs, platinum should last 75 - 100k miles with little or no wear, resisters should be replace every 35k. Also, use only import style plugs, i.e. denso, ngk, for your Camry. all others may give you grief later on.share printer on 2 computers codes for myspace
Does any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?
I changed the spark plugs and spark wires to new ones on the Dodge Caravan 2001, 3.3 litre engine.
When I started the engine the light on the dash board showed “engine trouble”
On the road the engine is not stable, especially with low RPM. When
I tried to accelerate and when I did, there was a sound in the engine area like a light low-sound explosion and it looked like the engine did not have enough power.
After the trip the dash board engine problem sign started to blink. I also checked the position wire on the sparks and it was in its correct position.
Does anybody know what the problem is and why it happened?
Thank you in advance for you answers.Does any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?If this problem only occured after you did this work then YES you need to back track and look at the plugs or crossed plug wires. Good Luck SirDoes any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?You got two spark plug wires backward.
With the engine running, unplug one spark plug wire from the distributor cap.
If the engine stumbles more or dies, plug it back in and try the next one.
As soon as you unplug one and nothing changes, that one is plugged into the wrong place.
There should be one more that is miss placed. When you find it , swap places in the distributor cap with the other %26quot;bad%26quot;one.Does any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?Double check the firing order. Sounds like you got one or more wires in the wrong place.Does any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?Changing spark plug wires are very funny thing meaning that you must be very correct about your application of the new hardware.Did you put the wires on backwards?, are your spark plugs gaped correctly,are they the rightrio spark plugs if this is not the problem, check the distributor cap's interior for cracks,burns,or broken electrode that extends to the rotor.Some times you mistakingnly broke the extentioner to the rotor therefore causing your problem.Also,even if the plug wires are new, they can be defective from the factory or the wires are packed too close to each other thus causing them to arc.open your hood at night without any light,start the vehicle and see if you see anysparks on any of the spark plug wires,if you do, you have a very bad wire, please change the wire.Is your distributor cap water tight?Does any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?Sounds like you might of crossed a wire or two and put them to the wrong spark plugDoes any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?Misfired,either wires were misplaced or spark plug's gap incorrect?Or the porcelain of the plug is cracked due to hard accessed of the inside bank when replacing.First,scan the PCM to see which cylinder is misfired ,or if you do not have scanner,take a closer look at the cables and plugs of the innner bank.Hope this helps.Does any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?Assuming the car was running decent prior to changing plugs and wires, it's logical that the problem lies somewhere in the process or possibly hardware involved with the spark plugs and wires. Giving the new plugs and wires the benefit of doubt, you may have accidentally plugged a wire onto the wrong plug. First check that each wire from the distributor is connected to the correct spark plug. Your owners manual may have a diagram to help with this task or you may have to visit the library and check out a shop manual. The following link may help as well: http://wiki.answers.com/Q/What_is_the_firing_order_for_a_1992_Dodge_Grand_Caravan_3.3L
If you determined that the wires are correct you may have a faulty wire or plug. If you are able to read the engine computer codes, it will point to the cylinder# with the problem. I've experienced this with my old Volvo. If you find the cylinder# but not sure if it's the plug or wire, try putting your old wire back in. If that fixes the problem, take the wire back to the store and have them give you a new wire. The same goes for the plug.Does any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?you need to clear the coad in the computer or it may get worse seriously you can clear acoad by disconnecting the batt + and - for min and then reconnect them should turn the light off but not fix the problem must take it in too the dealer to run a scan on the computer and it will cost $$ depending on what is wrong hope that helpedDoes any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?Hi,yeah you coulda crossed a couple wires but it may be as simple as you didn't put them on all the way go back and check them push them all the way down with a little twsting motion til you feel them %26quot;click%26quot; in place
When I started the engine the light on the dash board showed “engine trouble”
On the road the engine is not stable, especially with low RPM. When
I tried to accelerate and when I did, there was a sound in the engine area like a light low-sound explosion and it looked like the engine did not have enough power.
After the trip the dash board engine problem sign started to blink. I also checked the position wire on the sparks and it was in its correct position.
Does anybody know what the problem is and why it happened?
Thank you in advance for you answers.Does any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?If this problem only occured after you did this work then YES you need to back track and look at the plugs or crossed plug wires. Good Luck SirDoes any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?You got two spark plug wires backward.
With the engine running, unplug one spark plug wire from the distributor cap.
If the engine stumbles more or dies, plug it back in and try the next one.
As soon as you unplug one and nothing changes, that one is plugged into the wrong place.
There should be one more that is miss placed. When you find it , swap places in the distributor cap with the other %26quot;bad%26quot;one.Does any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?Double check the firing order. Sounds like you got one or more wires in the wrong place.Does any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?Changing spark plug wires are very funny thing meaning that you must be very correct about your application of the new hardware.Did you put the wires on backwards?, are your spark plugs gaped correctly,are they the rightrio spark plugs if this is not the problem, check the distributor cap's interior for cracks,burns,or broken electrode that extends to the rotor.Some times you mistakingnly broke the extentioner to the rotor therefore causing your problem.Also,even if the plug wires are new, they can be defective from the factory or the wires are packed too close to each other thus causing them to arc.open your hood at night without any light,start the vehicle and see if you see anysparks on any of the spark plug wires,if you do, you have a very bad wire, please change the wire.Is your distributor cap water tight?Does any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?Sounds like you might of crossed a wire or two and put them to the wrong spark plugDoes any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?Misfired,either wires were misplaced or spark plug's gap incorrect?Or the porcelain of the plug is cracked due to hard accessed of the inside bank when replacing.First,scan the PCM to see which cylinder is misfired ,or if you do not have scanner,take a closer look at the cables and plugs of the innner bank.Hope this helps.Does any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?Assuming the car was running decent prior to changing plugs and wires, it's logical that the problem lies somewhere in the process or possibly hardware involved with the spark plugs and wires. Giving the new plugs and wires the benefit of doubt, you may have accidentally plugged a wire onto the wrong plug. First check that each wire from the distributor is connected to the correct spark plug. Your owners manual may have a diagram to help with this task or you may have to visit the library and check out a shop manual. The following link may help as well: http://wiki.answers.com/Q/What_is_the_firing_order_for_a_1992_Dodge_Grand_Caravan_3.3L
If you determined that the wires are correct you may have a faulty wire or plug. If you are able to read the engine computer codes, it will point to the cylinder# with the problem. I've experienced this with my old Volvo. If you find the cylinder# but not sure if it's the plug or wire, try putting your old wire back in. If that fixes the problem, take the wire back to the store and have them give you a new wire. The same goes for the plug.Does any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?you need to clear the coad in the computer or it may get worse seriously you can clear acoad by disconnecting the batt + and - for min and then reconnect them should turn the light off but not fix the problem must take it in too the dealer to run a scan on the computer and it will cost $$ depending on what is wrong hope that helpedDoes any body know why something is wrong with the engine when you change spark plugs, spark wires to new one?Hi,yeah you coulda crossed a couple wires but it may be as simple as you didn't put them on all the way go back and check them push them all the way down with a little twsting motion til you feel them %26quot;click%26quot; in place
How do you change spark plugs?
In my pontiac grand am, I'm told that spark plugs are very easy to change (well, in almost any car they're easy). But could someone give me very straightforward directions just to make sure I don't screw it up? I know I need a spark plug puller (though I don't know what to do with it), and a socket wrench, which I have plenty of sizes and attachments for. I'm just looking for step-by-step. Thanks!How do you change spark plugs?http://www.wikihow.com/Change-Spark-Plugs-in-a-CarHow do you change spark plugs?here is some advice... do it one plug at a time. Remove the old plug, and put in the new one before moving on to the next plug. People often disconnect all the plug wires at once and then get confused which wire goes to which plug. If you do it wrong you could do some damage to your motor and it definately won't run properly.How do you change spark plugs?Gap the all plugs first, the spec should be on the sticker under the hood. Then remove the One spark plug boot by twisting and gently pulling or you will ruin the spark plug wire and remove that plug and replace. Do this procedure one at a time until all plugs have been changed.
Please voteHow do you change spark plugs?It is straight forward. Take the sprak plug wire off and put the socket on the spark plug. Unscrew it and pull it out. Put another one in and tighten it. Do them one at a time so you don't mix up the wires. If you put the wrong wire on the wrong plug, the engine wont run correctly.
Dont get the plugs too tight and be carefull when taking the plug wires off. If they are old, they may break.
A spark plug puller is basically a socket with a piece of rubber in it to grab and hold the spark plug.How do you change spark plugs?on those grand-ams you have to take the top off that goes on the engine and the plugs are down in there. you will need a long extension and a 5/8 socket and ratchet. make sure you gap them before installing them.
Please voteHow do you change spark plugs?It is straight forward. Take the sprak plug wire off and put the socket on the spark plug. Unscrew it and pull it out. Put another one in and tighten it. Do them one at a time so you don't mix up the wires. If you put the wrong wire on the wrong plug, the engine wont run correctly.
Dont get the plugs too tight and be carefull when taking the plug wires off. If they are old, they may break.
A spark plug puller is basically a socket with a piece of rubber in it to grab and hold the spark plug.How do you change spark plugs?on those grand-ams you have to take the top off that goes on the engine and the plugs are down in there. you will need a long extension and a 5/8 socket and ratchet. make sure you gap them before installing them.
How to change spark plugs in 2001 dodge durango?
v8 4.7L 4x4 dodge durango 2001 how would i change the spark plugs? loks liek the wires connected to it and it leads a long tube or shaft down into the cylinder chamber and it repeats this 7 more times to all other spark plugs.How to change spark plugs in 2001 dodge durango?you follow each wire to the engine pull the wire off then get a socket and take the old plug out and put the new one in. only do one at a time so you don't get the wires crossed because it can knock off your timing. you may also want to change wires too do them one at a time you will have to use the one you pull off and measure it to the new ones thanks hope this did not confuse you and hope it helps thanksHow to change spark plugs in 2001 dodge durango?why did you ask this question 3 times
How to I change spark plugs for my 2001 kia sportage? where are the located?
I have a 2001 kia sportage that is (well I think) backfireing and has no get up and go. I think it is the spark plugs. I have no idea where the are located or how to change them. CAN YOU HELP? I am a single mother with very little money, but I need my car fixed. ThanksHow to I change spark plugs for my 2001 kia sportage? where are the located?Hey Susanna....(no pun intended)
This IS NOT a job you want to attempt...in fact most mechanics would probably look at this and say ARG!
do yourself a favor and contact a local shop to price it out..and then save for it....I know that $ is an issue for you ...but this is way over your head.... it involves more than just spark plugs.
good luck.How to I change spark plugs for my 2001 kia sportage? where are the located?well you first look for them on the side of the block either behind or infron t and once located take a 13/16 socket and take one out and look at the number on the side of the plug and go to autozone or any parts dealer and tell them what you need . and do one at a time like take the plug wire off and then the plug out and put the plug in and wire back on.......your problem might be the fule filter tooo....How to I change spark plugs for my 2001 kia sportage? where are the located?Its a DOHC motor with the spark plugs running down the center of the cylinder head. You will need to remove the upper intake manifold to gain access to them. This is probably not a job for the novice.
This IS NOT a job you want to attempt...in fact most mechanics would probably look at this and say ARG!
do yourself a favor and contact a local shop to price it out..and then save for it....I know that $ is an issue for you ...but this is way over your head.... it involves more than just spark plugs.
good luck.How to I change spark plugs for my 2001 kia sportage? where are the located?well you first look for them on the side of the block either behind or infron t and once located take a 13/16 socket and take one out and look at the number on the side of the plug and go to autozone or any parts dealer and tell them what you need . and do one at a time like take the plug wire off and then the plug out and put the plug in and wire back on.......your problem might be the fule filter tooo....How to I change spark plugs for my 2001 kia sportage? where are the located?Its a DOHC motor with the spark plugs running down the center of the cylinder head. You will need to remove the upper intake manifold to gain access to them. This is probably not a job for the novice.
Can I change the spark plugs on my 99 Ply Voy Se 3.3 myself or is the three on the back side to hard?
I would like to change my spark plugs myself. However, the three plugs located on the back of the engine look quite hard to get to. Is it easier than I think or should I leave it to the experts. I have changed plugs before in other 4 cyl vehicles but none on 6 cyl engine positioned like this. What are your thoughts?Can I change the spark plugs on my 99 Ply Voy Se 3.3 myself or is the three on the back side to hard?Easiest to replace them from under the van.
Pretty challenging with basic tools.shark bed set hairdresser to bleach hair
Pretty challenging with basic tools.
How difficult is it to change spark plugs on a Ford Expedition?
I've changed spark plugs in a 2003 Mustang Mach 1 but I've heard horror stories about Expeditions. Is it worth me changing them or how much would it cost? ThanksHow difficult is it to change spark plugs on a Ford Expedition?Open the hood and decide for yourself........How difficult is it to change spark plugs on a Ford Expedition?It is a pain in the *** that is why the book time for it is over 2 hours, each spark plug has a coil over it and some of the bolts are covered by components and you have to tear them all off to get to them. I came close to telling my brother to piss off when he asked me to change his
How often do you change spark plugs 2002 hyundai elantra?
How often do you change the spark plugs on a 2002 hyundai elantraHow often do you change spark plugs 2002 hyundai elantra?The spark plugs that are in it should be platinum plugs. You can get between 80 and 100k miles out of them. Don't replace with something cheaper like resistor plugs. Go with what is recommended. They aren't that much more. And when you do replace the plugs, do the whole tune up. Cap and rotor if applicable, wires, pcv filter and air.How often do you change spark plugs 2002 hyundai elantra?These plugs (part #18814-11051) are not platinum and should be replaced every 40K or so. They are cheap $4/each, so why not?How often do you change spark plugs 2002 hyundai elantra?spoken like a true service manager lol why not he says because it cost money over time thats why not labor aint cheap at a dealer i say spend the bucks on some platinum plugs and find a shade tree mechanic and i say you will have to change them about every 80k miles maybe even more if you make sure to get some real nice plug wires tooHow often do you change spark plugs 2002 hyundai elantra?Twice a week
How and where do I change spark plugs on a 2001 Cadillac Deville?
My car was shaking after driving for awhile and someone told me that I had some cheap spark plugs in there. When I decided to change the spark plugs myself for the 1st time, I couldnt locate them. Can someone point me in the right direction? ThanksHow and where do I change spark plugs on a 2001 Cadillac Deville?you dont even know whats wrong...some guy told you? take it to a mechanic.
When to change spark plugs in my Pt Cruiser?
When do I need to change the spark plugs in my 2008 Pt Cruiser. It has 29k miles.
and when is a good time to change the belt?When to change spark plugs in my Pt Cruiser?You should consult your owners manual. Most newer vehicle suggest a tune up at 100,000 miles. I wouldn't wait that long if it were mine. I would replace the spark plugs around 60,000 miles. The timing belts are usually around the 100,000 mile mark.When to change spark plugs in my Pt Cruiser?We used to say, as an industry, change them every such and such mileage but the truth is that spark plugs have come worlds ahead of what was available when these intervals were conceived. More often than not you only need to change them every 100k unless something else has happened in your secondary ignition system causing one or all to foul. Just remember that when you do change them to go ahead and change the plug wires too, as they age you'll notice a whitish dust on them, this is known as electromagnetic interference or simply the aged wire is losing power throught it's cover and it attracts dust. Plugs and wires on you vehicle shouldn't cost more than about $60 if you do it yourself. Hope this helps.When to change spark plugs in my Pt Cruiser?29,000 no need yet
spark plugs might be good 100,000 miles
its when you notice a different in mileage or how your car is running
thats when you need a tune up
belts and hoses good for 3 to 5 yrs
you feel them to check look at them to see
type into search box
how to check belts
how to check hoses
read your owners manual
type
how to maintain a car
when to do car maintenance
you should be good to go but do
ask a shop to check it all out
next oil change a good time to have car check
tire rotated
brakes looked at
to know its needs and when it needs
dont say you need it replace
just ask to have it check
might be getting close to a tune up
you dont fix whats not broken
any shop you choose you ask them to check first
many shops check it all every time some dont
and just look after what you say i needs thinking you know
have it check when you do oil changes better you keep up with this car maintenance
cheaper it is to maintain it know what your cars need are you need to learn that part that what keeps it running and saves you a walk in the rain
learn your car needs
and whens save you money and helps stop from being takingWhen to change spark plugs in my Pt Cruiser?you still have a good while to wait before changing the plugs and belt. i,am supposing your talking about the timing belt. you still should have a waranty on that car.When to change spark plugs in my Pt Cruiser?i agree with frankie, but i believe the owners manual for a pt cruiser suggests 70,000 or 75,000 miles for the belt. the owners manual says it all!When to change spark plugs in my Pt Cruiser?This will all be detailed in the owners service manual. The bit the garage stamps when you get it serviced - presuming that you do.
and when is a good time to change the belt?When to change spark plugs in my Pt Cruiser?You should consult your owners manual. Most newer vehicle suggest a tune up at 100,000 miles. I wouldn't wait that long if it were mine. I would replace the spark plugs around 60,000 miles. The timing belts are usually around the 100,000 mile mark.When to change spark plugs in my Pt Cruiser?We used to say, as an industry, change them every such and such mileage but the truth is that spark plugs have come worlds ahead of what was available when these intervals were conceived. More often than not you only need to change them every 100k unless something else has happened in your secondary ignition system causing one or all to foul. Just remember that when you do change them to go ahead and change the plug wires too, as they age you'll notice a whitish dust on them, this is known as electromagnetic interference or simply the aged wire is losing power throught it's cover and it attracts dust. Plugs and wires on you vehicle shouldn't cost more than about $60 if you do it yourself. Hope this helps.When to change spark plugs in my Pt Cruiser?29,000 no need yet
spark plugs might be good 100,000 miles
its when you notice a different in mileage or how your car is running
thats when you need a tune up
belts and hoses good for 3 to 5 yrs
you feel them to check look at them to see
type into search box
how to check belts
how to check hoses
read your owners manual
type
how to maintain a car
when to do car maintenance
you should be good to go but do
ask a shop to check it all out
next oil change a good time to have car check
tire rotated
brakes looked at
to know its needs and when it needs
dont say you need it replace
just ask to have it check
might be getting close to a tune up
you dont fix whats not broken
any shop you choose you ask them to check first
many shops check it all every time some dont
and just look after what you say i needs thinking you know
have it check when you do oil changes better you keep up with this car maintenance
cheaper it is to maintain it know what your cars need are you need to learn that part that what keeps it running and saves you a walk in the rain
learn your car needs
and whens save you money and helps stop from being takingWhen to change spark plugs in my Pt Cruiser?you still have a good while to wait before changing the plugs and belt. i,am supposing your talking about the timing belt. you still should have a waranty on that car.When to change spark plugs in my Pt Cruiser?i agree with frankie, but i believe the owners manual for a pt cruiser suggests 70,000 or 75,000 miles for the belt. the owners manual says it all!When to change spark plugs in my Pt Cruiser?This will all be detailed in the owners service manual. The bit the garage stamps when you get it serviced - presuming that you do.
How do I change spark plugs and replace spark plug wires on a 1987 Camaro V-6?
I am a woman and I am getting ripped off by mechanics and I need my spark plugs changed and wires replaced. I am running on about 3 cylinders right now. Please help someoneHow do I change spark plugs and replace spark plug wires on a 1987 Camaro V-6?the best advice is to replace them one at a time to avoid confusion :)How do I change spark plugs and replace spark plug wires on a 1987 Camaro V-6?replace one at a time, plug ,wire, that way you cant mess up anything . use anti sieze on plugs .How do I change spark plugs and replace spark plug wires on a 1987 Camaro V-6?you need tools, pull one boot at a time, I own an IROC Z-28, and the plugs and wires on a V-8 is a pain to change.How do I change spark plugs and replace spark plug wires on a 1987 Camaro V-6?TAKE A PLACE OF TAPE AND PLACE ON EACH WIRE LIKE FIRST WIRE PUT ONE PICE AND2 PUT 2 PICES AND SO ONHow do I change spark plugs and replace spark plug wires on a 1987 Camaro V-6?Get a new car that will fix all problems.medium hair advice for younger brother
How to change spark plugs and wires?
I have a 2002 Chrysler town %26amp; country Limited with 105K miles on it. Due to very low mileage (12 mpg), I need to change the spark plugs (and possibly wires). I will appreciate if anybody could provide me instructions (Do's and Dont's) so that I can do it on my own. ThanksHow to change spark plugs and wires?Make sure you mark the position of each wire. Make sure you have the proper spark plug socket (with a rubber insert in it to protect the plug) Don't over tighten the new plug when installing them. There is not much more.How to change spark plugs and wires?I just changed the plugs on our 2002 town and country. All the sites I saw said that you had to remove a bunch of stuff to get at the rear plugs. I was able to reach back there and get at them. I had to use extensions of various lengths with my sockets, but I was able to get at them. Took 1 hour.
one end will be where you place plugs into the engine the other end will be your distributor cap - as you take out plugs from your dist cap make sure you number them with tape ( masking tape ) this is your fireing order and you do not want to mess this up -
buy the pregapped plugs if your not familiar with changing them this way you dont have to worry about the gaping tool - i cant stand them personally -
and basically all you have to do is unplugg from each end replace your plug and wires -
since you arent getting good milage consider replaceing your air filter also -How to change spark plugs and wires?View the Advance Auto online %26quot;todays tuneups%26quot; video for the basic spark plug and wire installation
http://www.advanceautoparts.com/english/How to change spark plugs and wires?go to the parts store, pick up a haynes maintenance manual, how many cylinders does your engine have, pick up that many spark plugs, and wires, rent or buy a torque wrench, a distributer cap and rotor and an airfilter. mark everything where you find it. if you want to save a bit of money, skip the manual (they are handy to have for other maintenance stuff, though) and get everything else. You can get the torque values from the internet and the firing order should be stamped on the engine block, also the cylinder numbers should also be stamped on the block. Before you remove the wires, mark them the same as the cylinder numbers from which you removed them. leave them attatched to the distributer cap!!!! But make sure you mark them to match the cylinder mark on the block!! Then remove and replace the plugs, use the torque values. . . check each plug as they come out. there should be a nice uniform greyish white burnt look to them. note where the ones that look different came from and use the internet to find out what could have caused any irregular deposits on them. Then one by one replace the wires, making sure that you plug them all up to the same reciever on the distributer cap from which you removed them ONE AT A TIME!!! , them, remove the distributer cap, and line it up with the old one and trade the wires over to the new one, one by one, making sure that they are all in the SAME place they were on the old one, set aside, replace the rotor, you just pull it out and put the new one in, in the same position you found the old one in. then you reattatch the distributer cap and you should be on your way with MUCH better gas mileage!! Oh!! also replace your airfilter. . . umm you might also replace your fuel filter as well, sometimes it gets clogged up and messes with you mileage. . .? Good luck and I hope I helped some!! ^_^
Report Abuse
How to change spark plugs and wires?well you should easily be able to locate your spark plug wires and that would be the easiest thing -one end will be where you place plugs into the engine the other end will be your distributor cap - as you take out plugs from your dist cap make sure you number them with tape ( masking tape ) this is your fireing order and you do not want to mess this up -
buy the pregapped plugs if your not familiar with changing them this way you dont have to worry about the gaping tool - i cant stand them personally -
and basically all you have to do is unplugg from each end replace your plug and wires -
since you arent getting good milage consider replaceing your air filter also -How to change spark plugs and wires?View the Advance Auto online %26quot;todays tuneups%26quot; video for the basic spark plug and wire installation
http://www.advanceautoparts.com/english/How to change spark plugs and wires?go to the parts store, pick up a haynes maintenance manual, how many cylinders does your engine have, pick up that many spark plugs, and wires, rent or buy a torque wrench, a distributer cap and rotor and an airfilter. mark everything where you find it. if you want to save a bit of money, skip the manual (they are handy to have for other maintenance stuff, though) and get everything else. You can get the torque values from the internet and the firing order should be stamped on the engine block, also the cylinder numbers should also be stamped on the block. Before you remove the wires, mark them the same as the cylinder numbers from which you removed them. leave them attatched to the distributer cap!!!! But make sure you mark them to match the cylinder mark on the block!! Then remove and replace the plugs, use the torque values. . . check each plug as they come out. there should be a nice uniform greyish white burnt look to them. note where the ones that look different came from and use the internet to find out what could have caused any irregular deposits on them. Then one by one replace the wires, making sure that you plug them all up to the same reciever on the distributer cap from which you removed them ONE AT A TIME!!! , them, remove the distributer cap, and line it up with the old one and trade the wires over to the new one, one by one, making sure that they are all in the SAME place they were on the old one, set aside, replace the rotor, you just pull it out and put the new one in, in the same position you found the old one in. then you reattatch the distributer cap and you should be on your way with MUCH better gas mileage!! Oh!! also replace your airfilter. . . umm you might also replace your fuel filter as well, sometimes it gets clogged up and messes with you mileage. . .? Good luck and I hope I helped some!! ^_^
When Should we change the spark plugs on a 2005 chevy avalanche?
We got this truck brand new and we use it for daily use but when should i Change Spark plugsWhen Should we change the spark plugs on a 2005 chevy avalanche?I'm a GM Tech, and I will tell you that if your vehicle is running OK then don't worry about the plugs for 100,000 miles. Don't pull them out and inspect them because there is too much potential for breaking a plug or damaging a spark plug wire.
Trust me on this!When Should we change the spark plugs on a 2005 chevy avalanche?I recommend replacing them at 50,000 miles. Do not wait till 100K. Most times the plugs will be seized in the head at 100K and will take a lot of time and money to repair.
Always use antiseize on the threads when re-installing the new plugs.When Should we change the spark plugs on a 2005 chevy avalanche?See what the owners manual says. As a bit of added info...I have never in my 45 years of working on cars used anti sieze on spark plugs. You should just make sure they are tightened to the proper torque.When Should we change the spark plugs on a 2005 chevy avalanche?100,000 miles. This is pretty much standard for all General Motors products. When you change them, use double platinum plugs and you can go another 100,000 miles.
Newer engines with aluminum heads require anti-sieze or you will damage the threads the next time you remove them. And yes, this engine has aluminum heads.When Should we change the spark plugs on a 2005 chevy avalanche?Replacement should be done at the 100k mark. They are a platinum long life plug.
The problem with waiting that long is that over time they may become seized in the head.
I suggest you remove the plugs and inspect them. If they look OK wait till the mileage gets to 100k. At least then you won't have any removal problems, and they are quite easy to get at on your Chevy.When Should we change the spark plugs on a 2005 chevy avalanche?change them a 100k and don't got to some jack leg autoparts store to get plugs and wires.Go to the GM dealer and use oem parts.They last longer and come gapped to spec. all you have to do is put them in.When Should we change the spark plugs on a 2005 chevy avalanche?at the dealership we recommend a tune up(air filter, pcv valve and plugs) as a part of the 60 thousand mile service along with a fuel filter, tranny filter and pan gasket, and several additives w/ other routine maintenece, this can be done anywhere but these we recommend every 60k, good luckWhen Should we change the spark plugs on a 2005 chevy avalanche?Most manufactures recommend 100,000 miles for a tune up which includes changing the fuel filter at the same time as the spark plugsWhen Should we change the spark plugs on a 2005 chevy avalanche?100,000 miles if you would have problem bring it to dealer under warrantee yes plugs are warranteedWhen Should we change the spark plugs on a 2005 chevy avalanche?I'd take a look at them @ 50,000 miles and check the gaps with a round gap gage. The standard plugs are iridium therefore outlast platinum by 2-1. You should however change the stubby little plug wires at 50,000. Don't skimp on plug wires. Replace with AC Delco. If it happens that MSD makes tailor fitted wires at that time they would be my first choice.When Should we change the spark plugs on a 2005 chevy avalanche?we have a maintenance package called an smo6 which is supposes to be done every 30000 thousand miles which includes spark plugs but really you can wait until around 90000 or 100000 miles but when you do use some anti seize just some cheap insurance but yea be sure they are also gaped correctly and they DONT come pre gaped from the factory the spark plugs you dont gap are the iridium those are the good onesWhen Should we change the spark plugs on a 2005 chevy avalanche?I do it on my car every 30,000 miles when most require it to be around 75,000When Should we change the spark plugs on a 2005 chevy avalanche?GM recommends 100,000,miles (could not tell you what it is in KM). Gm does not highly recommend pulling out plugs to inspect and then reinstalling them. Personally me, anytime after 70,000 miles and use anti seize compound since the engine has aluminum heads. I used Autolite Platnium XP's and was amazed on my 2002 chevy venture around 70,000 miles, its performance.
Trust me on this!When Should we change the spark plugs on a 2005 chevy avalanche?I recommend replacing them at 50,000 miles. Do not wait till 100K. Most times the plugs will be seized in the head at 100K and will take a lot of time and money to repair.
Always use antiseize on the threads when re-installing the new plugs.When Should we change the spark plugs on a 2005 chevy avalanche?See what the owners manual says. As a bit of added info...I have never in my 45 years of working on cars used anti sieze on spark plugs. You should just make sure they are tightened to the proper torque.When Should we change the spark plugs on a 2005 chevy avalanche?100,000 miles. This is pretty much standard for all General Motors products. When you change them, use double platinum plugs and you can go another 100,000 miles.
Newer engines with aluminum heads require anti-sieze or you will damage the threads the next time you remove them. And yes, this engine has aluminum heads.When Should we change the spark plugs on a 2005 chevy avalanche?Replacement should be done at the 100k mark. They are a platinum long life plug.
The problem with waiting that long is that over time they may become seized in the head.
I suggest you remove the plugs and inspect them. If they look OK wait till the mileage gets to 100k. At least then you won't have any removal problems, and they are quite easy to get at on your Chevy.When Should we change the spark plugs on a 2005 chevy avalanche?change them a 100k and don't got to some jack leg autoparts store to get plugs and wires.Go to the GM dealer and use oem parts.They last longer and come gapped to spec. all you have to do is put them in.When Should we change the spark plugs on a 2005 chevy avalanche?at the dealership we recommend a tune up(air filter, pcv valve and plugs) as a part of the 60 thousand mile service along with a fuel filter, tranny filter and pan gasket, and several additives w/ other routine maintenece, this can be done anywhere but these we recommend every 60k, good luckWhen Should we change the spark plugs on a 2005 chevy avalanche?Most manufactures recommend 100,000 miles for a tune up which includes changing the fuel filter at the same time as the spark plugsWhen Should we change the spark plugs on a 2005 chevy avalanche?100,000 miles if you would have problem bring it to dealer under warrantee yes plugs are warranteedWhen Should we change the spark plugs on a 2005 chevy avalanche?I'd take a look at them @ 50,000 miles and check the gaps with a round gap gage. The standard plugs are iridium therefore outlast platinum by 2-1. You should however change the stubby little plug wires at 50,000. Don't skimp on plug wires. Replace with AC Delco. If it happens that MSD makes tailor fitted wires at that time they would be my first choice.When Should we change the spark plugs on a 2005 chevy avalanche?we have a maintenance package called an smo6 which is supposes to be done every 30000 thousand miles which includes spark plugs but really you can wait until around 90000 or 100000 miles but when you do use some anti seize just some cheap insurance but yea be sure they are also gaped correctly and they DONT come pre gaped from the factory the spark plugs you dont gap are the iridium those are the good onesWhen Should we change the spark plugs on a 2005 chevy avalanche?I do it on my car every 30,000 miles when most require it to be around 75,000When Should we change the spark plugs on a 2005 chevy avalanche?GM recommends 100,000,miles (could not tell you what it is in KM). Gm does not highly recommend pulling out plugs to inspect and then reinstalling them. Personally me, anytime after 70,000 miles and use anti seize compound since the engine has aluminum heads. I used Autolite Platnium XP's and was amazed on my 2002 chevy venture around 70,000 miles, its performance.
When is a good time to change spark plugs on a newer vehicle?
Does anyone have a good idea if I should change my spark plugs for my 2005 Explorer Sport Trac? I'm sure it is recommended to change @ 100K miles. I'm currently at 57+K and was wondering if it would do me any good to change them now. I just would like to get more HP or MPG's if this would help. Thank youWhen is a good time to change spark plugs on a newer vehicle?well those are iridium tipped plugs they will last 100000 miles without really losing mpg or hp the only problem is getting them out of the head after 100000!!!When is a good time to change spark plugs on a newer vehicle?if your going to buy a better plug (im still not sure they save gas not sure) then go for it try it out but just pull one out unless its got build up on it or corosion then replacing wont make a diff either way not going to change hp unless urs is running bad u can change chips in them to gain hp but ur going to lose mpg gl hope this helps uWhen is a good time to change spark plugs on a newer vehicle?75K use best you can get...
How to change spark plugs inside cars?
Hello again =]
I had an Xterra 01 and I'm sure i have to change spark plugs. But since i never done it and I don't want to ruin or break them inside I wonder if some1 can tell me exactly and what tools to use to change them?
It's all the same for every cars?.. Same tools same methods?How to change spark plugs inside cars?It's the same for every car.
1) Remove the cover, if there is one (usually says DOHC or some nonsense like that).
2) Remove the wires, making note of their order (crucial). If you have a four cylinder, there will be four.
3) Using a spark plug socket that fits your car (this differs car-to-car), unscrew the spark plugs
4) Gap the new spark plugs, if needed
5) Gently install the new spark plugs by finger tightening, then using your ratchet to just snug it in place - do not overtighten!
6) Replace wires and cover, making sure the wires go back on in the correct order
Just be gentle, don't force anything, and you'll be fine. It might be the easiest thing to do next to replacing the air filter.How to change spark plugs inside cars?It's pretty straight forward. Find spark plugs, remove spark plug wires, unscrew/remove spark plugs, screw/install new plugs, replace wires.
Here is a simple guide with pictures:
http://autorepair.about.com/od/regularma
It becomes difficult if the plugs are in a tight spot with little clearance, I'm not sure how it is on your car.
To be sure to get the right spark plug socket, buy the plugs from an auto parts store, then remove one from the box and find the socket that fits it.
Tip: Either label the spark plug wires, or do one at a time. You don't want to mix up which wires go on which plugs.
I had an Xterra 01 and I'm sure i have to change spark plugs. But since i never done it and I don't want to ruin or break them inside I wonder if some1 can tell me exactly and what tools to use to change them?
It's all the same for every cars?.. Same tools same methods?How to change spark plugs inside cars?It's the same for every car.
1) Remove the cover, if there is one (usually says DOHC or some nonsense like that).
2) Remove the wires, making note of their order (crucial). If you have a four cylinder, there will be four.
3) Using a spark plug socket that fits your car (this differs car-to-car), unscrew the spark plugs
4) Gap the new spark plugs, if needed
5) Gently install the new spark plugs by finger tightening, then using your ratchet to just snug it in place - do not overtighten!
6) Replace wires and cover, making sure the wires go back on in the correct order
Just be gentle, don't force anything, and you'll be fine. It might be the easiest thing to do next to replacing the air filter.How to change spark plugs inside cars?It's pretty straight forward. Find spark plugs, remove spark plug wires, unscrew/remove spark plugs, screw/install new plugs, replace wires.
Here is a simple guide with pictures:
http://autorepair.about.com/od/regularma
It becomes difficult if the plugs are in a tight spot with little clearance, I'm not sure how it is on your car.
To be sure to get the right spark plug socket, buy the plugs from an auto parts store, then remove one from the box and find the socket that fits it.
Tip: Either label the spark plug wires, or do one at a time. You don't want to mix up which wires go on which plugs.
How can you tell its time to change spark plugs?
I have a 2006 Chevy Impala LTZ 3.9Lt. with 129000 kms. When and how can you tell its time to change the spark plugs. What is the average life of the current spark plugs.How can you tell its time to change spark plugs?During periodic service of 5,000 to 10,000 kms, changing spark plugs are one of the requirements. Failed to change spark plugs can cause, jerking, stalling and hard starting in the morning. Don't wait for the spark plug to malfunctions, i suggest to change it as you service your car. Hope this helps!How can you tell its time to change spark plugs?Most plugs for your year should be change every 100k miles, is car running rough or poor gas mileage.How can you tell its time to change spark plugs?usually about 50k will do it/unleaded gas and allHow can you tell its time to change spark plugs?I'm not any good at converting metric to american, but they're approximately 4 years old now. and are about due. if you notice any misfire on cold starts, especially in wet or damp weather, that is an indication. the bottom line is, for the price of a tune-up, you can more likely add a mile or two per gallon to your fuel average... over a period of time... the tuneup save you money.How can you tell its time to change spark plugs?typically...once every year. if your car has the originals (2006) i believe its safe to say you probably could use a set..How can you tell its time to change spark plugs?When the car doesnt start lolPDA long hair cut
How do I change spark plugs in my 1500 Vulcan?
I bot a 1998 1500 Vulcan last week and it seems to be missing some. I want to change the spark plugs but was wondering if there is a trick to it. I dont mean to soung stupid, but I tried pulling on the plug wires and it would not come off.How do I change spark plugs in my 1500 Vulcan?my answer is try to check it out first on auto repair shop..dude
How often do you change Spark Plugs in your boat?
I have a 2003 Ebbtide Campoine 18.5' Mercruiser 4.3 V6 Alpha one. I just pulled it out of storage started doing the normal routine of cleaning and mechanical upkeep. Gear lube and Oil has been changed before storage (everything up to par) my question is regarding the spark plugs...
When should you change them? Is 3 years too soon? (I'll pull one out tonight and look for corrosion, etc).
Also any other spring time engine recommendations for a 4 year old boat?How often do you change Spark Plugs in your boat?When is the last time you changed your water pump impeller . if you cant remember you maybe due. Real important they get weak with age and take a set when sittng to long and become weak.
If you pull your plugs and the white insulator around the center electrode is light brown they are good . A correct burning plug thats what color it should be Be sure to check all the bellows behind the drives bellhousing and look for drycracking between the webs. if you see any you need it changed.How often do you change Spark Plugs in your boat?As you mentioned, just inspect them. If, the Anode/Electrode not look badly worn they probably OK for another season.
I not have a boat now and am looking, but, the last I had, I kept year round in a slip. Summer it was beached at the camp area and used most everyday. I usually changed plugs in it every summer. It probably got more use than a car.
I tried to find some pictures, many manuals show different plug wear. It a personal preference, but, I do use a little Anti-Seize on my Plugs.How often do you change Spark Plugs in your boat?You fire up on the old spark plugs from the season before, the motor should have been %26quot;fogged%26quot; before it was winterized, burn the old oil out of the motor at start up (IT SMOKES), THEN replace the spark plugs, why foul up %26quot;NEW%26quot; plugs ? they should be changed every spring, changing over to %26quot;NEW%26quot; spark plugs makes a world of difference on an outboard motor, don't forget, it burns %26quot;MIX%26quot;, not straight gasoline like a car (if it's a 2 stroke outboard), so they get dirtier faster than a car's spark plugs.How often do you change Spark Plugs in your boat?I change them at least every 100 hours and clean them at least once a year.How often do you change Spark Plugs in your boat?Just do it every year when it comes out of storage, they are cheap.
When should you change them? Is 3 years too soon? (I'll pull one out tonight and look for corrosion, etc).
Also any other spring time engine recommendations for a 4 year old boat?How often do you change Spark Plugs in your boat?When is the last time you changed your water pump impeller . if you cant remember you maybe due. Real important they get weak with age and take a set when sittng to long and become weak.
If you pull your plugs and the white insulator around the center electrode is light brown they are good . A correct burning plug thats what color it should be Be sure to check all the bellows behind the drives bellhousing and look for drycracking between the webs. if you see any you need it changed.How often do you change Spark Plugs in your boat?As you mentioned, just inspect them. If, the Anode/Electrode not look badly worn they probably OK for another season.
I not have a boat now and am looking, but, the last I had, I kept year round in a slip. Summer it was beached at the camp area and used most everyday. I usually changed plugs in it every summer. It probably got more use than a car.
I tried to find some pictures, many manuals show different plug wear. It a personal preference, but, I do use a little Anti-Seize on my Plugs.How often do you change Spark Plugs in your boat?You fire up on the old spark plugs from the season before, the motor should have been %26quot;fogged%26quot; before it was winterized, burn the old oil out of the motor at start up (IT SMOKES), THEN replace the spark plugs, why foul up %26quot;NEW%26quot; plugs ? they should be changed every spring, changing over to %26quot;NEW%26quot; spark plugs makes a world of difference on an outboard motor, don't forget, it burns %26quot;MIX%26quot;, not straight gasoline like a car (if it's a 2 stroke outboard), so they get dirtier faster than a car's spark plugs.How often do you change Spark Plugs in your boat?I change them at least every 100 hours and clean them at least once a year.How often do you change Spark Plugs in your boat?Just do it every year when it comes out of storage, they are cheap.
How do I change the spark plugs on an Infiniti QX4?
I would like know how to change spark plugs Specifically for an Infiniti QX4. I would also like to know what tools will I need to perform this task. I was told that the spark plugs on an Infiniti are positioned differently from other cars. This is why I am asking specific details on changing spark plugs for an Infiniti QX4.How do I change the spark plugs on an Infiniti QX4?Not as straight forward an operation as you might hope. First, locate the coil packs. The Infiniti has a small coil mounted on top of each spark plug. This is why you will not see any heavy gauge spark plug wires running from a coil or distributor to the obvious location of the spark plug. The coil packs are attached with a 10mm bolt. In many cases other items, (air filter assembly, brackets loaded with stuff) must be removed even to see the coil packs. Be very careful with the coils as they are expensive to replace. The coil pack will reach down into the engine 8-10%26quot; to where the spark plug actually sits. You will need a long socket adapter to reach in and actually remove the spark plug. To change all 6 plugs, plan to spend about three hours if you have never done this before.How do I change the spark plugs on an Infiniti QX4?you should either get ahold of the repair manual (or online version like alldata) to make sure you do it correctly with all the right torques.
Or find an Infiniti forum and ask there to see if others have done it and written it up.
The spark plugs themselves should be pretty standard procedure, but likely you need to loosen and move a bunch of parts to access them, which is the harder part.
Or find an Infiniti forum and ask there to see if others have done it and written it up.
The spark plugs themselves should be pretty standard procedure, but likely you need to loosen and move a bunch of parts to access them, which is the harder part.
Should I change spark plug wires since I am replacing spark plugs?
I want to replace spark plugs in my car.
Primary reason is it has 80k miles and I think it needs changing. Second is spark plugs are very cheap. Only $2 per spark plug. I was wondering if I should be change spark plug wires as well since I would have to remove them to get to spark plugs. Or just change spark plugs and keep old wires. Bad part is wires themselves are kind of expensive, about $40 I think.Should I change spark plug wires since I am replacing spark plugs?Yes! The wires can be slightly bad %26amp; only misfire sometimes but still cost you more than $40 in gas over a years time.Should I change spark plug wires since I am replacing spark plugs?If the wires show not signs of wear, it is probably safe to keep the old wires. That said, for $40 to $50, I would replace the wires along with the plugs. As another answer suggested, it is important to ensure the wires are not crossed during replacement. The easiest way to prevent that is to only remove one wire at a time, and replace it before removing any more wires.Should I change spark plug wires since I am replacing spark plugs?Since the car is at 80k i would change the wires as well. Only remove one wire at a time and put the new wire on, then take off the next wire. If you remove them all you could have trouble remembering which one goes where.Should I change spark plug wires since I am replacing spark plugs?my shop would recommend wires but personally if your not having any problems they should last at least 100-120k.unless they have already been replaced by cheap wires then i would spring for the new QUALITY wires.(delco,motorcraft,etc)
Primary reason is it has 80k miles and I think it needs changing. Second is spark plugs are very cheap. Only $2 per spark plug. I was wondering if I should be change spark plug wires as well since I would have to remove them to get to spark plugs. Or just change spark plugs and keep old wires. Bad part is wires themselves are kind of expensive, about $40 I think.Should I change spark plug wires since I am replacing spark plugs?Yes! The wires can be slightly bad %26amp; only misfire sometimes but still cost you more than $40 in gas over a years time.Should I change spark plug wires since I am replacing spark plugs?If the wires show not signs of wear, it is probably safe to keep the old wires. That said, for $40 to $50, I would replace the wires along with the plugs. As another answer suggested, it is important to ensure the wires are not crossed during replacement. The easiest way to prevent that is to only remove one wire at a time, and replace it before removing any more wires.Should I change spark plug wires since I am replacing spark plugs?Since the car is at 80k i would change the wires as well. Only remove one wire at a time and put the new wire on, then take off the next wire. If you remove them all you could have trouble remembering which one goes where.Should I change spark plug wires since I am replacing spark plugs?my shop would recommend wires but personally if your not having any problems they should last at least 100-120k.unless they have already been replaced by cheap wires then i would spring for the new QUALITY wires.(delco,motorcraft,etc)
How to change spark plugs on Dodge Stratus 2002 4cyl?
I am trying to change my spark plugs but can not seem to get to them. There is rubber wire coming to the spark plug place and regardless how hard i pull this rubber base it does not come off. Can someone explain me how to get this rubber cap off so i can access spark plug ?
Thanks,
Please do not post some standard spark plug instruction that you simply copy pasted from some random website.How to change spark plugs on Dodge Stratus 2002 4cyl?you have to loosen the mounts unhook the tranny and tilt the enginereptiles dog
Thanks,
Please do not post some standard spark plug instruction that you simply copy pasted from some random website.How to change spark plugs on Dodge Stratus 2002 4cyl?you have to loosen the mounts unhook the tranny and tilt the engine
Subscribe to:
Posts
(Atom)